www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNA LABS / Challenge Labs Solutions / Challenge Lab 3 Solution: EIGRP, PAT, ACLs and Banners

Challenge Lab 3 Solution: EIGRP, PAT, ACLs and Banners

Task 1 Hints & References

For reference information on configuring hostnames, please refer to:

Lab 21 Configuration and Verification Task 1

Lab 35 Configuration and Verification Task 1

Task 2 Hints & References

To bring up the interfaces, you need to perform a no shutdown command on the interface.

For reference information on configuring and verifying VLANs, please refer to:

Lab 1 Configuration and Verification Task 3

Lab 2 Configuration and Verification Task 3

Task 3 Hints & References

Each router must have two Frame Relay map statements similar to the following:

Serial1/0 (up): ip [IP ADDRESS] dlci [DLCI](0x66,0x1860), static,

broadcast,

CISCO, status defined, active

Serial1/0 (up): ip [IP ADDRESS] dlci [DLCI](0x67,0x1870), static,

broadcast,

CISCO, status defined, active

For reference information on verifying Frame Relay mapping, please refer to:

Lab 26 Configuration and Verification Task 3

Lab 27 Configuration and Verification Task 3

Lab 40 Configuration and Verification Task 4

Lab 40 Configuration and Verification Task 5

Task 4 Hints & References

For reference information on using standard PING, please refer to:

Lab 15 Configuration and Verification Task 6

Task 5 Hints & References

Your EIGRP configuration on R2 would be:

router eigrp 2000

no auto-summary

network 10.0.0.0 0.0.0.31

If you did not use the wildcard mask, EIGRP would advertise the entire 10.0.0.0/8 network, which would include the 10.1.1.0/24 subnet. Since that is prohibited in the lab, you must use the EIGRP wildcard mask.

For reference information wildcard masks, please refer to:

Lab 42 Configuration and Verification Task 5

Lab 48 Configuration and Verification Task 3

For reference information on enabling EIGRP, please refer to:

Lab 41 Configuration and Verification Task 4

Lab 42 Configuration and Verification Task 5

Lab 44 Configuration and Verification Task 5

For reference information on verifying EIGRP adjacencies, please refer to:

Lab 41 Configuration and Verification Task 5

Lab 42 Configuration and Verification Task 7

Task 6 Hints & References

Use the show ip route eigrp or the show ip route command to verify routing information.

Task 7 Hints & References

You need to use the ip route 0.0.0.0 0.0.0.0 [interface|ip address] command

For reference information on configuring static routes, please refer to:

Lab 31 Configuration and Verification Task 4

Lab 32 Configuration and Verification Task 3

Lab 33 Configuration and Verification Task 4

Lab 34 Configuration and Verification Task 4

To configure an MOTD banner, you need to use the banner motd command. Be careful not to use your delimiting character in the banner configuration!

For reference information on configuring banners, please refer to:

Lab 78 Configuration and Verification Task 2

Task 8 Hints & References

You need to configure an extended ACL for the PAT traffic. Your ACL would be similar to the following:

ip access-list extended NAT-ACL

permit icmp 10.1.1.0 0.0.0.255 172.16.1.0 0.0.0.127 echo

permit icmp 10.1.1.0 0.0.0.255 172.16.1.0 0.0.0.127 echo-reply

permit icmp 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.63 echo

permit icmp 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.63 echo-reply

You then need to use this ACL in the ip nat inside command and PAT traffic to S0/0

For reference information on NAT, please refer to:

Lab 65 Configuration and Verification Task 6

Lab 66 Configuration and Verification Task 7

Lab 67 Configuration and Verification Task 7

Lab 68 Configuration and Verification Task 7

Lab 59 Configuration and Verification Task 6

Task 9 Hints & References

You need to add to the ACL you created in Task 8 to complete this task

ip access-list extended NAT-ACL

permit tcp 10.1.1.0 0.0.0.255 10.0.0.0 0.0.0.31 eq telnet

Alternatively, you can create a second PAT configuration altogether:

ip nat inside source-list TELNET-NAT-ACL interface Serial0/0 overload

ip nat inside source-list PING-NAT-ACL interface Serial0/0 overload

!

ip access-list extended NAT-ACL

permit tcp 10.1.1.0 0.0.0.255 10.0.0.0 0.0.0.31 eq telnet

!

ip access-list extended PING-NAT-ACL

permit icmp 10.1.1.0 0.0.0.255 172.16.1.0 0.0.0.127 echo

permit icmp 10.1.1.0 0.0.0.255 172.16.1.0 0.0.0.127 echo-reply

permit icmp 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.63 echo

permit icmp 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.63 echo-reply

Whichever method you use, as long as it meets the requirements, you’re fine.

For reference information on configuring NAT, please refer to:

Lab 65 Configuration and Verification Task 6

Lab 66 Configuration and Verification Task 8

Lab 67 Configuration and Verification Task 7

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.