Task 1:
For reference information on configuring hostnames, please refer to:
Lab 20 Configuration and Verification Task 1
Lab 21 Configuration and Verification Task 1
Task 2:
For reference information on verifying DTE/DCE status, please refer to:
Lab 20 Configuration and Verification Task 2
Lab 21 Configuration and Verification Task 2
For reference information on configuring DCE clocking, please refer to:
Lab 21 Configuration and Verification Task 2
Task 3:
For reference information on enabling PPP encapsulation, please refer to:
Lab 22 Configuration and Verification Task 3
Lab 23 Configuration and Verification Task 3
Task 4:
For reference information on verifying Serial encapsulation, please refer to:
Lab 21 Configuration and Verification Task 5
Lab 22 Configuration and Verification Task 5
R1#ping 192.168.50.34
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.50.34, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms
R2#ping 192.168.50.33
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.50.33, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms
Task 5:
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#int s0/0
R1(config-if)#ppp authentication chap
R1(config-if)#ppp chap ?
hostname Set alternate CHAP hostname
password Set default CHAP password
refuse Refuse to authenticate using CHAP
wait Wait for caller to authenticate first
R1(config-if)#ppp chap hostname Router1
R1(config-if)#ppp chap password MyPass
R1(config-if)#exit
R1(config)#username Router2 password MyPass
R1(config)#end
R1#
R2#configure ter
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#interf ser 0/0
R2(config-if)#ppp authentication chap
R2(config-if)#ppp chap hostname Router2
R2(config-if)#ppp chap password MyPass
R2(config-if)#exit
R2(config)#username Router1 password MyPass
R2(config)#end
R2#
| NOTE: By default, there is no need to configure a hostname to be used for CHAP authentication on Cisco IOS routers as they will use the hostname configured on the router. However, to use a different hostname, CHAP must be configured for that. This is performed using the ppp chap hostname and ppp chap password commands on the PPP interface used for CHAP authentication. |
Task 6:
R2#debug ppp authentication
PPP authentication debugging is on
R2#config t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#int s0/0
R2(config-if)#shut
*Mar 1 03:54:08.805: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down
*Mar 1 03:54:09.807: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
R2(config-if)#no shut
*Mar 1 03:54:15.861: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
*Mar 1 03:54:15.861: Se0/0 PPP: Using default call direction
*Mar 1 03:54:15.861: Se0/0 PPP: Treating connection as a dedicated line
*Mar 1 03:54:15.861: Se0/0 PPP: Session handle[D50000E3] Session id[229]
*Mar 1 03:54:15.861: Se0/0 PPP: Authorization required
*Mar 1 03:54:15.869: Se0/0 CHAP: O CHALLENGE id 181 len 28 from “Router2”
*Mar 1 03:54:15.869: Se0/0 CHAP: I CHALLENGE id 181 len 28 from “Router1”
*Mar 1 03:54:15.873: Se0/0 CHAP: Using hostname from interface CHAP
*Mar 1 03:54:15.877: Se0/0 CHAP: Using password from AAA
*Mar 1 03:54:15.877: Se0/0 CHAP: O RESPONSE id 181 len 28 from “Router2”
*Mar 1 03:54:15.877: Se0/0 CHAP: I RESPONSE id 181 len 28 from “Router1”
*Mar 1 03:54:15.881: Se0/0 PPP: Sent CHAP LOGIN Request
*Mar 1 03:54:15.881: Se0/0 PPP: Received LOGIN Response PASS
*Mar 1 03:54:15.885: Se0/0 PPP: Sent LCP AUTHOR Request
*Mar 1 03:54:15.885: Se0/0 PPP: Sent IPCP AUTHOR Request
*Mar 1 03:54:15.885: Se0/0 CHAP: I SUCCESS id 181 len 4
*Mar 1 03:54:15.889: Se0/0 LCP: Received AAA AUTHOR Response PASS
*Mar 1 03:54:15.889: Se0/0 IPCP: Received AAA AUTHOR Response PASS
*Mar 1 03:54:15.889: Se0/0 CHAP: O SUCCESS id 181 len 4
*Mar 1 03:54:15.893: Se0/0 PPP: Sent CDPCP AUTHOR Request
*Mar 1 03:54:15.897: Se0/0 PPP: Sent IPCP AUTHOR Request
*Mar 1 03:54:15.897: Se0/0 CDPCP: Received AAA AUTHOR Response PASS
*Mar 1 03:54:16.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
R2(config-if)#end
R2#
*Mar 1 03:54:21.114: %SYS-5-CONFIG_I: Configured from console by console
R2#undebug ppp authentication
PPP authentication debugging is off
R2#