www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNA LABS / Wide Area Networks Solutions / Lab 29 Solution: Configuring Frame Relay point-to-point Subinterfaces

Lab 29 Solution: Configuring Frame Relay point-to-point Subinterfaces

Task 1:

Router#config t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#host R1

R1(config)#interface s1/0

R1(config-if)#encapsulation frame-relay

R1(config-if)#^Z

R1#

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hostname R2

R2(config)#int s0/0

R2(config-if)#encap frame-relay

R2(config-if)#end

R2#

Task 2:

R1#configure te

Enter configuration commands, one per line.  End with CNTL/Z.

R1(config)#int s1/0.100 ?

multipoint      Treat as a multipoint link

point-to-point  Treat as a point-to-point link

NOTE: Notice that you have the option of configuring either a multipoint subinterface or a point-to-point subinterface when configuring Frame Relay subinterfaces. In this case, we want point-to-point.

R1(config)#int s1/0.100 point-to-point

R1(config-subif)#ip address 192.168.5.5 255.255.255.252

R1(config-subif)#frame-relay interface-dlci 111

R1(config-fr-dlci)#end

R1#

NOTE: Also notice that we assign a DLCI to a point-to-point subinterface using the frame-relay interface-dlci command. You cannot use the frame-relay map command on a point-to-point subinterface. However, you can use the frame-relay interface-dlci command on a multipoint subinterface or physical interface. Multipoint subinterfaces behave and are configured in the same manner as physical interfaces.

R1#show ip interface brief

Interface                  IP-Address      OK? Method Status  Protocol

Serial1/0                  unassigned      YES manual  up       up

Serial1/0.100            192.168.5.5     YES manual  up       up

R2#config t

Enter configuration commands, one per line.  End with CNTL/Z.

R2(config)#interface serial 0/0.200 point-to-point

R2(config-subif)#ip address 192.168.5.6 255.255.255.252

R2(config-subif)#frame-relay interface-dlci 222

R2(config-fr-dlci)#^Z

R2#

R2#sh ip int bri

Interface                  IP-Address      OK? Method Status Protocol

Serial0/0                  unassigned      YES manual  up       up

Serial0/0.200            192.168.5.6     YES manual  up       up

Task 3:

R1#show frame-relay map

Serial1/0.100 (up): point-to-point dlci, dlci 111(0x6F,0x18F0), broadcast

status defined, active

R1#ping 192.168.5.6

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.5.6, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 8/8/8 ms

R2#show frame-relay map

Serial0/0.200 (up): point-to-point dlci, dlci 222(0xDE,0x34E0), broadcast

status defined, active

R2#ping 192.168.5.5

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.5.5, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 8/8/8 ms

NOTE: Notice that unlike the output of the show frame-relay map command when using Inverse ARP or static DLCI mapping on physical interfaces, the same output does not provide the IP address mapped to the remote end for point-to-point subinterfaces. This is because there can only be two end points on a point-to-point connection unlike a physical or multipoint connection that can have more than two. Also notice that, by default, Broadcast and Multicast capabilities are enabled for the DLCIs.

 

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.