www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNP Labs Solutions / CCNP Lab 014 Solution: EIGRP Multi-Technology Lab

CCNP Lab 014 Solution: EIGRP Multi-Technology Lab

Lab Objective:

The focus of this lab is to understand EIGRP implementation and configuration in Cisco IOS routers. Additional technologies tested include stub routing, filtering, and authentication.

Lab Topology:

The lab network topology is illustrated below:

department614

 

IMPORTANT NOTE

If you are using the www.howtonetwork.net racks, please bring up the LAN interfaces connected to the routers by issuing the no shutdown command on the connected switches. If you are using a home lab with no
Switches, you can bring up the LAN interfaces using the following configurations on your routers:

interface fastethernet 0/0
 no keepalive
 loopback
 no shutdown

Alternately, you can simply connect the interfaces to a hub or switch if you have one available in your own lab. Also, if you are using the www.howtonetwork.net racks, configure R3 as the Frame Relay switch using the following configuration commands:

hostname R3-Frame-Relay-Switch
!
frame-relay switching
!
interface serial 1/0
 description ‘Connected To R1 Serial 0/1’
 encapsulation frame-relay
 no ip address
 clock rate 128000
 frame-relay intf-type dce
 frame-relay route 102 interface serial 1/1 201
 frame-relay route 104 interface serial 1/2 401
 no shutdown
!
interface serial 1/1
 description ‘Connected To R2 Serial 0/1’
 encapsulation frame-relay
 no ip address
 clock rate 128000
 frame-relay intf-type dce
 frame-relay route 201 interface serial 1/0 102
 no shutdown
!
interface serial 1/2
 description ‘Connected To R4 Serial 0/0’
 encapsulation frame-relay
 no ip address
 clock rate 128000
 frame-relay intf-type dce
 frame-relay route 401 interface serial 1/0 104
 no shutdown
!
end

 

Task 1

Configure hostnames and IP addressing on all routers as illustrated in the network topology.

Task 2

Configure EIGRP for AS 1 as illustrated in the topology. However, do NOT advertise the 150.x.x.x subnets on any router via EIGRP.

Task 3

Configure routers R2 and R4 to as EIGRP stub routers. These routers should advertise their 150.x.x.x/24 subnets as Internal EIGRP routes to R1.

Task 4

Configure R1 so that it advertises ONLY a default route to both R2 and R4 as an External EIGRP route. Next, verify your configuration using the appropriate commands. Additionally, also verify that R2 and R4 can ping each others’ 150.x.x.x/24 subnets from their LAN interfaces, as well as the 150.1.1.0/24 subnet on R1s LAN.

 

 

Task 5

Configure EIGRP authentication for AS 1 so that all the routers use the password CCNP-2010; however, after 15 minutes, the routers should stop using this password and begin using the password CCNP-2011. The password CCNP-2011 should be used by all routers indefinitely. Verify your configuration using the appropriate commands.

Lab Validation

Task 1

Router(config)#hostname R1
R1(config)#interface fastethernet 0/0
R1(config-if)#no shutdown
R1(config-if)#ip address 150.1.1.1 255.255.255.0
R1(config-if)#exit
R1(config)#interface serial 0/1
R1(config-if)#ip address 10.0.0.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#encapsulation frame-relay
R1(config-if)#exit
Router(config)#hostname R2
R2(config)#interface fastethernet 0/0
R2(config-if)#no shutdown
R2(config-if)#ip address 150.2.2.2 255.255.255.0
R2(config-if)#exit
R2(config)#interface serial 0/1
R2(config-if)#ip address 10.0.0.2 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#encapsulation frame-relay
R2(config-if)#exit
Router(config)#hostname R4
R4(config)#interface fastethernet 0/0
R4(config-if)#no shutdown
R4(config-if)#ip address 150.4.4.4 255.255.255.0
R4(config-if)#exit
R4(config)#interface serial 0/0
R4(config-if)#ip address 10.0.0.4 255.255.255.0
R4(config-if)#no shutdown
R4(config-if)#encapsulation frame-relay
R4(config-if)#exit

Task 2

R1(config)#router eigrp 1
R1(config-router)#no auto-summary
R1(config-router)#network 10.0.0.1 0.0.0.0
R1(config-router)#exit
R2(config)#router eigrp 1
R2(config-router)#no auto-summary
R2(config-router)#network 10.0.0.2 0.0.0.0
R2(config-router)#exit
R4(config)#router eigrp 1
R4(config-router)#no auto-summary
R4(config-router)#network 10.0.0.4 0.0.0.0
R4(config-router)#exit

Use the show ip eigrp neighbors command to verify your configuration:

R1#show ip eigrp neighbors
IP-EIGRP neighbors for process 1
H   Address                 Interface       Hold Uptime   SRTT   RTO  Q  Seq
(sec)         (ms)       Cnt Num
1   10.0.0.4                Se0/1            135 00:00:46   16   200  0  3
0   10.0.0.2                Se0/1            157 00:01:20   15   200  0  3
R2#show ip eigrp neighbors
IP-EIGRP neighbors for process 1
H   Address                 Interface       Hold Uptime   SRTT   RTO  Q  Seq
(sec)         (ms)       Cnt Num
0   10.0.0.1                Se0/1            166 00:01:39 1264  5000  0  3
R4#show ip eigrp neighbors 
IP-EIGRP neighbors for process 1
H   Address                 Interface       Hold Uptime   SRTT   RTO  Q  Seq
(sec)         (ms)       Cnt Num
0   10.0.0.1                Se0/0            151 00:01:19 1219  5000  0  5

Task 3

By default, EIGRP stub routers advertise connected and summary routes. Therefore, no explicit configuration other than enabling EIGRP for the 150.x.x.x/24 subnets is required:

R2(config)#router eigrp 1
R2(config-router)#network 150.2.2.2 0.0.0.0
R2(config-router)#eigrp stub
R2(config-router)#exit
R4(config)#router eigrp 1
R4(config-router)#network 150.4.4.4 0.0.0.0
R4(config-router)#eigrp stub
R4(config-router)#exit

Verify your configuration using the show ip eigrp neighbors detail command on R1:

R1#show ip eigrp neighbors detail
IP-EIGRP neighbors for process 1
H   Address                 Interface       Hold Uptime   SRTT   RTO  Q  Seq
(sec)         (ms)       Cnt Num
1   10.0.0.4                Se0/1            160 00:00:21 1253  5000  0  8
Version 12.4/1.2, Retrans: 0, Retries: 0, Prefixes: 1
Stub Peer Advertising ( CONNECTED SUMMARY ) Routes
Suppressing queries

0   10.0.0.2                Se0/1            161 00:02:15  654  3924  0  7
Version 12.4/1.2, Retrans: 0, Retries: 0, Prefixes: 1
Stub Peer Advertising ( CONNECTED SUMMARY ) Routes
Suppressing queries

Alternatively, you can use the show ip protocols command on the stub routers:

R2#show ip protocols
Routing Protocol is “eigrp 1”
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Default networks flagged in outgoing updates
Default networks accepted from incoming updates
EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0
EIGRP maximum hopcount 100
EIGRP maximum metric variance 1
EIGRP stub, connected, summary
Redistributing: eigrp 1
EIGRP NSF-aware route hold timer is 240s
Automatic network summarization is not in effect
Maximum path: 4
Routing for Networks:
10.0.0.2/32
150.2.2.2/32
Routing Information Sources:
Gateway         Distance      Last Update
10.0.0.1              90      00:01:39
Distance: internal 90 external 170
R4#show ip protocols
Routing Protocol is “eigrp 1”
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Default networks flagged in outgoing updates
Default networks accepted from incoming updates
EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0
EIGRP maximum hopcount 100
EIGRP maximum metric variance 1
EIGRP stub, connected, summary
Redistributing: eigrp 1
EIGRP NSF-aware route hold timer is 240s
Automatic network summarization is not in effect
Maximum path: 4
Routing for Networks:
10.0.0.4/32
150.4.4.4/32
Routing Information Sources:
Gateway         Distance      Last Update
10.0.0.1              90      00:00:48
Distance: internal 90 external 170

Verify that the routes are received on R1 using the show ip route [eigrp] command:

R1#show ip route eigrp
150.2.0.0/24 is subnetted, 1 subnets
D       150.2.2.0 [90/2172416] via 10.0.0.2, 00:05:26, Serial0/1
150.4.0.0/24 is subnetted, 1 subnets
D       150.4.4.0 [90/2172416] via 10.0.0.4, 00:03:32, Serial0/1

Task 4

The task is to advertise an external default route to R2 and R4. Because split horizon is enabled by default, R1 will not advertise the 150.2.2.0/24 and 150.3.3.0/24 subnets out the same interface via which they were received, so no explicit filtering configuration for EIGRP is required on R1. This task is completed as follows:

R1(config)#ip route 0.0.0.0 0.0.0.0 null 0
R1(config)#router eigrp 1
R1(config-router)#redistribute static
R1(config-router)#exit

Verify your configuration by looking at the routing tables on R2 and R4:

R2#show ip route eigrp
D*EX 0.0.0.0/0 [170/2169856] via 10.0.0.1, 00:00:35, Serial0/1
R4#show ip route eigrp
D*EX 0.0.0.0/0 [170/2169856] via 10.0.0.1, 00:00:53, Serial0/0

Verify IP connectivity using simple pings:

R1#ping 150.2.2.2 source 150.1.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.2.2.2, timeout is 2 seconds:
Packet sent with a source address of 150.1.1.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms

R1#ping 150.4.4.4 source 150.1.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.4.4.4, timeout is 2 seconds:
Packet sent with a source address of 150.1.1.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms

R2#ping 150.1.1.1 source 150.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 150.2.2.2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms

R2#ping 150.4.4.4 source 150.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.4.4.4, timeout is 2 seconds:
Packet sent with a source address of 150.2.2.2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms

R4#ping 150.1.1.1 source 150.4.4.4

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 150.4.4.4
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms

R4#ping 150.2.2.2 source 150.4.4.4

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 150.2.2.2, timeout is 2 seconds:
Packet sent with a source address of 150.4.4.4
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms

Task 5

There are several ways in which this task can be completed. One way would be to synchronize the router clocks by manually setting the system clock using the clock set command or using Network Time Protocol (NTP).  If this solution is used, this task is completed as follows:

R1(config)#clock timezone CST -6
R1(config)#clock summer-time CST recurring
R1(config)#ntp master
R1(config)#exit
R2(config)#clock timezone CST -6
R2(config)#clock summer-time CST recurring
R2(config)#ntp server 10.0.0.1
R2(config)#exit
R4(config)#clock timezone CST -6
R4(config)#clock summer-time CST recurring
R4(config)#ntp server 10.0.0.1
R4(config)#exit

Verify Network Time Protocol and clock settings using the show ntp status command:

R4#show ntp status
Clock is synchronized, stratum 9, reference is 10.0.0.1
nominal freq is 250.0000 Hz, actual freq is 250.0000 Hz, precision is 2**18
reference time is D170B71D.82C8E0A7 (01:30:53.510 CST Sun May 8 2011)
clock offset is -0.0292 msec, root delay is 24.98 msec
root dispersion is 125.11 msec, peer dispersion is 125.05 msec

Following this configuration, you can then configure EIGRP authentication as follows:

R1(config)#key chain EIGRP-AUTH
R1(config-keychain)#key 1
R1(config-keychain-key)#key-string CCNP-2010
R1(config-keychain-key)#accept local 01:45:00 May 8 2011 02:00:00 May 8 2011
R1(config-keychain-key)#send local 01:45:00 May 8 2011 02:00:00 May 8 2011
R1(config-keychain-key)#exit
R1(config-keychain)#key 2
R1(config-keychain-key)#key-string CCNP-2011
R1(config-keychain-key)#accept-lifetime local 02:00:00 May 8 2011 infinite
R1(config-keychain-key)#send-lifetime local 02:00:00 May 8 2011 infinite
R1(config-keychain-key)#exit
R1(config-keychain)#exit
R1(config)#interface serial 0/0
R1(config-if)#ip authentication mode eigrp 1 md5
R1(config-if)#ip authentication key-chain eigrp 1 EIGRP-AUTH
R1(config-if)#exit
R2(config)#key chain EIGRP-AUTH
R2(config-keychain)#key 1
R2(config-keychain-key)#key-string CCNP-2010
R2(config-keychain-key)#accept local 01:45:00 May 8 2011 02:00:00 May 8 2011
R2(config-keychain-key)#send local 01:45:00 May 8 2011 02:00:00 May 8 2011
R2(config-keychain-key)#exit
R2(config-keychain)#key 2
R2(config-keychain-key)#key-string CCNP-2011
R2(config-keychain-key)#accept-lifetime local 02:00:00 May 8 2011 infinite
R2(config-keychain-key)#send-lifetime local 02:00:00 May 8 2011 infinite
R2(config-keychain-key)#exit
R2(config-keychain)#exit
R2(config)#interface serial 0/1
R2(config-if)#ip authentication mode eigrp 1 md5
R2(config-if)#ip authentication key-chain eigrp 1 EIGRP-AUTH
R2(config-if)#exit
R4(config)#key chain EIGRP-AUTH
R4(config-keychain)#key 1
R4(config-keychain-key)#key-string CCNP-2010
R4(config-keychain-key)#accept local 01:45:00 May 8 2011 02:00:00 May 8 2011
R4(config-keychain-key)#send local 01:45:00 May 8 2011 02:00:00 May 8 2011
R4(config-keychain-key)#exit
R4(config-keychain)#key 2
R4(config-keychain-key)#key-string CCNP-2011
R4(config-keychain-key)#accept-lifetime local 02:00:00 May 8 2011 infinite
R4(config-keychain-key)#send-lifetime local 02:00:00 May 8 2011 infinite
R4(config-keychain-key)#exit
R4(config-keychain)#exit
R4(config)#interface serial 0/0
R4(config-if)#ip authentication mode eigrp 1 md5
R4(config-if)#ip authentication key-chain eigrp 1 EIGRP-AUTH
R4(config-if)#exit

 

Following this, verify key chain configuring using the show key chain command:

R1#show clock
01:54:36.175 CST Sun May 8 2011

R1#show key chain EIGRP-AUTH
Key-chain EIGRP-AUTH:
    key 1 — text “CCNP-2010”
        accept lifetime (01:45:00 CST May 8 2011) – (02:00:00 CST May 8 2011) [valid now]
        send lifetime (01:45:00 CST May 8 2011) – (02:00:00 CST May 8 2011) [valid now]
key 2 — text “CCNP-2011”
accept lifetime (02:00:00 CST May 8 2011) – (infinite)
send lifetime (02:00:00 CST May 8 2011) – (infinite)

After the configured time interval has elapsed, the second key is used and the first invalidated:

R1#show key chain EIGRP-AUTH
Key-chain EIGRP-AUTH:
key 1 — text “CCNP-2010”
accept lifetime (01:45:00 CST May 8 2011) – (02:00:00 CST May 8 2011)
send lifetime (01:45:00 CST May 8 2011) – (02:00:00 CST May 8 2011)
    key 2 — text “CCNP-2011”
        accept lifetime (02:00:00 CST May 8 2011) – (infinite) [valid now]
        send lifetime (02:00:00 CST May 8 2011) – (infinite) [valid now]

The second method would simply be to specify the duration in the key chain. To do this, you will need to know the local time on each router, which is why the synchronized time, i.e. NTP, method is better – especially if you have multiple routers. This is completed as follows:

R1(config)#key chain EIGRP-AUTH
R1(config-keychain)#key 1
R1(config-keychain-key)#key-string CCNP-2010
R1(config-keychain-key)#send-lifetime 01:45:00 May 8 2011 duration 900
R1(config-keychain-key)#accept-lifetime 01:45:00 May 8 2011 duration 900
R1(config-keychain-key)#exit
R1(config-keychain)#exit
R1(config)#key chain EIGRP-AUTH
R1(config-keychain)#key 2
R1(config-keychain-key)#key-string CCNP-2011
R1(config-keychain-key)#accept 02:00:00 May 8 2011 infinite
R1(config-keychain-key)#exit

NOTE: The duration Â is specified in seconds. 15 minutes = 900 seconds.

R1#show key chain EIGRP-AUTH
Key-chain EIGRP-AUTH:
    key 1 — text “CCNP-2010”
        accept lifetime (01:45:00 UTC May 8 2011) – (900 seconds) [valid now]
        send lifetime (01:45:00 UTC May 8 2011) – (900 seconds) [valid now]
key 2 — text “CCNP-2011”
accept lifetime (02:00:00 UTC May 8 2011) – (infinite)
send lifetime (02:00:00 UTC May 8 2011) – (infinite)

After the configured time interval has elapsed, the second key is used and the first invalidated:

R1#show key chain EIGRP-AUTH
Key-chain EIGRP-AUTH:
key 1 — text “CCNP-2010”
accept lifetime (01:45:00 UTC May 8 2011) – (900 seconds)
send lifetime (01:45:00 UTC May 8 2011) – (900 seconds)
    key 2 — text “CCNP-2011”
        accept lifetime (02:00:00 UTC May 8 2011) – (infinite) [valid now]
        send lifetime (02:00:00 UTC May 8 2011) – (infinite) [valid now]

Final Router Configurations

R1

 

R1#term len 0
R1#sh run
Building configuration…

Current configuration : 1478 bytes
!
! Last configuration change at 01:52:43 CST Sun May 8 2011
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
clock timezone CST -6
clock summer-time CST recurring
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
key chain EIGRP-AUTH
key 1
key-string CCNP-2010
accept-lifetime local 01:45:00 May 8 2011 02:00:00 May 8 2011
send-lifetime local 01:45:00 May 8 2011 02:00:00 May 8 2011
key 2
key-string CCNP-2011
accept-lifetime local 02:00:00 May 8 2011 infinite
send-lifetime local 02:00:00 May 8 2011 infinite
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.1.1.1 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
no ip address
ip authentication mode eigrp 1 md5
ip authentication key-chain eigrp 1 EIGRP-AUTH
shutdown
clock rate 2000000
!
interface Serial0/1
ip address 10.0.0.1 255.255.255.0
encapsulation frame-relay
!
router eigrp 1
redistribute static
network 10.0.0.1 0.0.0.0
no auto-summary
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Null0
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
ntp master
!
end

R1#

R2

 

R2#term len 0
R2#sh run
Building configuration…

Current configuration : 1414 bytes
!
! Last configuration change at 02:02:25 CST Sun May 8 2011
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
clock timezone CST -6
clock summer-time CST recurring
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
key chain EIGRP-AUTH
key 1
key-string CCNP-2010
accept-lifetime local 01:45:00 May 8 2011 02:00:00 May 8 2011
send-lifetime local 01:45:00 May 8 2011 02:00:00 May 8 2011
key 2
key-string CCNP-2011
accept-lifetime local 02:00:00 May 8 2011 infinite
send-lifetime local 02:00:00 May 8 2011 infinite
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.2.2.2 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
!
interface Serial0/1
ip address 10.0.0.2 255.255.255.0
encapsulation frame-relay
!
router eigrp 1
network 10.0.0.2 0.0.0.0
network 150.2.2.2 0.0.0.0
no auto-summary
eigrp stub connected summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
ntp clock-period 17179893
ntp server 10.0.0.1
!
end

R2#

R3

 

R3-Frame-Relay-Switch#term len 0
R3-Frame-Relay-Switch#sh run
Building configuration…

Current configuration : 1656 bytes
!
! Last configuration change at 02:03:34 UTC Sun May 8 2011
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R3-Frame-Relay-Switch
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
frame-relay switching
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial1/0
description ‘Connected To R1 Serial 0/1’
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay intf-type dce
frame-relay route 102 interface Serial1/1 201
frame-relay route 104 interface Serial1/2 401
!
interface Serial1/1
description ‘Connected To R2 Serial 0/1’
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay intf-type dce
frame-relay route 201 interface Serial1/0 102
!
interface Serial1/2
description ‘Connected To R4 Serial 0/0’
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay intf-type dce
frame-relay route 401 interface Serial1/0 104
!
interface Serial1/3
no ip address
shutdown
!
interface Serial1/4
no ip address
shutdown
!
interface Serial1/5
no ip address
shutdown
!
interface Serial1/6
no ip address
shutdown
!
interface Serial1/7
no ip address
shutdown
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R3-Frame-Relay-Switch#

R4

 

R4#term len 0
R4#sh run
Building configuration…

Current configuration : 1414 bytes
!
! Last configuration change at 01:52:40 CST Sun May 8 2011
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R4
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
clock timezone CST -6
clock summer-time CST recurring
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
key chain EIGRP-AUTH
key 1
key-string CCNP-2010
accept-lifetime local 01:45:00 May 8 2011 02:00:00 May 8 2011
send-lifetime local 01:45:00 May 8 2011 02:00:00 May 8 2011
key 2
key-string CCNP-2011
accept-lifetime local 02:00:00 May 8 2011 infinite
send-lifetime local 02:00:00 May 8 2011 infinite
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.4.4.4 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.4 255.255.255.0
encapsulation frame-relay
!
interface Serial0/1
no ip address
shutdown
!
router eigrp 1
network 10.0.0.4 0.0.0.0
network 150.4.4.4 0.0.0.0
no auto-summary
eigrp stub connected summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
ntp clock-period 17179872
ntp server 10.0.0.1
!
end

R4#

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.