www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNP Labs Solutions / CCNP Lab 026 Solution: OSPF Multi-Technology Lab

CCNP Lab 026 Solution: OSPF Multi-Technology Lab

Lab Objective:

The focus of this lab is to understand OSPF implementation and configuration in Cisco IOS routers. Additional technologies tested include path control and backbone connectivity.

Lab Topology:

The lab network topology is illustrated below:

department626

 

 

IMPORTANT NOTE

If you are using the www.howtonetwork.net racks, please bring up the LAN interfaces connected to the routers by issuing the no shutdown command on the connected switches. If you are using a home lab with no
Switches, you can bring up the LAN interfaces using the following configurations on your routers:

interface fastethernet 0/0
 no keepalive
 loopback
 no shutdown

Alternately, you can simply connect the interfaces to a hub or switch if you have one available in your own lab. Also, if you are using the www.howtonetwork.net racks, configure R3 as the Frame Relay switch using the following configuration commands:

hostname R3-Frame-Relay-Switch
!
frame-relay switching
!
interface serial 1/0
 description ‘Connected To R1 Serial 0/1’
 encapsulation frame-relay
 no ip address
 clock rate 128000
 frame-relay intf-type dce
 frame-relay route 102 interface serial 1/1 201
 frame-relay route 104 interface serial 1/2 401
 no shutdown
!
interface serial 1/1
 description ‘Connected To R2 Serial 0/1’
 encapsulation frame-relay
 no ip address
 clock rate 128000
 frame-relay intf-type dce
 frame-relay route 201 interface serial 1/0 102
 no shutdown
!
interface serial 1/2
 description ‘Connected To R4 Serial 0/0’
 encapsulation frame-relay
 no ip address
 clock rate 128000
 frame-relay intf-type dce
 frame-relay route 401 interface serial 1/0 104
 no shutdown
!
end

 

Task 1

Configure hostnames and IP addressing on all routers as illustrated in the network topology.

Task 2

Configure the Frame Relay network so that all routers can ping each others’ WAN interfaces.

Task 3

Using interface-based configuration, configure OSPF over the Frame Relay WAN connectivity R1, R2, and R4, as well as on the LAN segment connected to R1. Ensure that there is no DR/BDR election on the WAN segment. Also, ensure that no Hellos or LSAs are flooded out of the LAN segment. Finally, ensure that OSPF uses Multicast packets when sending updates over the WAN. Verify your configuration using the appropriate commands.

Task 4

Configure the 192.168.0.0/24 subnet on the LAN segment between R2 and R4. In addition, also configure a secondary IP subnet of 192.168.1.0/24 on the LAN segment between R2 and R4. Using interface-based configuration, configure OSPF area 1 on the LAN segment between R1 and R2. Ensure that both the primary 192.168.0.0/24 and secondary 192.168.1.0/24 subnets are advertised as internal OSPF routes. Verify that R1 can ping both subnets.

 

Task 5

Without modifying any interface bandwidth or cost values, or default administrative distance values, configure OSPF so that R1 prefers the path via R2 to reach the 192.168.0.0/24 and prefers the path via R4 to reach the 192.168.1.0/24 subnet. Verify your path control configuration using the appropriate commands.

Task 6

Configure OSPF so that R1 and R2 establish an OSPF adjacency in area 5. Do NOT enable OSPF for the point-to-point link, i.e. the 10.0.1.0/30 subnet, between R1 and R2. Implement your configuration so that when the Frame Relay network is unavailable, the 192.168.0.0/24 and the 192.168.1.0/24 subnets can still communicate with the 150.1.1.0/24 subnet. Verify your OSPF configuration using the appropriate commands.

Lab Validation

Task 1

Router(config)#hostname R1
R1(config)#interface fastethernet 0/0
R1(config-if)#no shutdown
R1(config-if)#ip address 150.1.1.1 255.255.255.0
R1(config-if)#exit
R1(config)#interface serial 0/0
R1(config-if)#no shutdown
R1(config-if)#ip address 10.0.1.1 255.255.255.252
R1(config-if)#clock rate 2000000
R1(config-if)#exit
R1(config)#interface serial 0/1
R1(config-if)#ip address 10.0.0.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#encapsulation frame-relay
R1(config-if)#exit
Router(config)#hostname R2
R2(config)#interface fastethernet 0/0
R2(config-if)#no shutdown
R2(config-if)#ip address 150.5.5.2 255.255.255.0
R2(config-if)#exit
R2(config)#interface serial 0/0
R2(config-if)#no shutdown
R2(config-if)#ip address 10.0.1.2 255.255.255.252
R2(config-if)#exit
R2(config)#interface serial 0/1
R2(config-if)#ip address 10.0.0.2 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#encapsulation frame-relay
R2(config-if)#exit
Router(config)#hostname R4
R4(config)#interface fastethernet 0/0
R4(config-if)#ip address 150.5.5.4 255.255.255.0
R4(config-if)#exit
R4(config)#interface serial 0/0
R4(config-if)#ip address 10.0.0.4 255.255.255.0
R4(config-if)#no shutdown
R4(config-if)#encapsulation frame-relay
R4(config-if)#exit

Task 2
Although Frame Relay configuration is not a CCNP topic, per se, it is still important that you remember your Frame Relay configurations from the CCNA. The task is completed as follows:

R1(config)#interface serial 0/1
R1(config-if)#frame-relay map ip 10.0.0.2 102 broadcast
R1(config-if)#frame-relay map ip 10.0.0.4 104 broadcast
R1(config-if)#exit

On the spoke routers, because the same DLCI is being used, the broadcast keyword should only be specified once to avoid duplicate Broadcast packets across the Frame Relay WAN. This task is completed as follows:

R2(config)#interface serial 0/1
R2(config-if)#frame-relay map ip 10.0.0.1 201 broadcast
R2(config-if)#frame-relay map ip 10.0.0.4 201        Â
R2(config-if)#exit
R4(config)#interface serial 0/0
R4(config-if)#frame-relay map ip 10.0.0.1 401 broadcast
R4(config-if)#frame-relay map ip 10.0.0.2 401        Â
R4(config-if)#exit

Verify your Frame Relay configuration using the show frame-relay map command:

R1#show frame-relay map
Serial0/1 (up): ip 10.0.0.2 dlci 102(0x66,0x1860), static,
broadcast,
CISCO, status defined, active
Serial0/1 (up): ip 10.0.0.4 dlci 104(0x68,0x1880), static,
broadcast,
CISCO, status defined, active
R2#show frame-relay map
Serial0/1 (up): ip 10.0.0.1 dlci 201(0xC9,0x3090), static,
broadcast,
CISCO, status defined, active
Serial0/1 (up): ip 10.0.0.4 dlci 201(0xC9,0x3090), static,
CISCO, status defined, active
R4#show frame-relay map
Serial0/0 (up): ip 10.0.0.1 dlci 401(0x191,0x6410), static,
broadcast,
CISCO, status defined, active
Serial0/0 (up): ip 10.0.0.2 dlci 401(0x191,0x6410), static,
CISCO, status defined, active

Finally, verify that you can ping between all routers across the Frame Relay WAN:

R1#ping 10.0.0.2 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 28/29/32 ms
R1#
R1#ping 10.0.0.4 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 10.0.0.4, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 28/29/32 ms

R2#ping 10.0.0.1 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 28/30/32 ms
R2#
R2#ping 10.0.0.4 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 10.0.0.4, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 56/59/64 ms

R4#ping 10.0.0.1 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 28/34/52 ms
R4#
R4#ping 10.0.0.2 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 56/58/60 ms

Task 3

To complete this task, you need to configure a point-to-multipoint network type. This will allow OSPF to use Multicast but prevent DR/BDR election. This task is completed as follows:

R1(config)#router ospf 1
R1(config-router)#router-id 1.1.1.1
R1(config-router)#passive-interface fastethernet 0/0
R1(config-router)#exit
R1(config)#interface fastethernet 0/0
R1(config-if)#ip ospf 1 area 0
R1(config-if)#exit
R1(config)#interface serial 0/1
R1(config-if)#ip ospf network point-to-multipoint
R1(config-if)#ip ospf 1 area 0
R1(config-if)#exit
R2(config)#router ospf 2
R2(config-router)#router-id 2.2.2.2
R2(config-router)#exit
R2(config)#interface serial 0/1
R2(config-if)#ip ospf network point-to-multipoint
R2(config-if)#ip ospf 2 area 0
R2(config-if)#exit
R4(config)#router ospf 4
R4(config-router)#router-id 4.4.4.4
R4(config-router)#exit
R4(config)#interface serial 0/0
R4(config-if)#ip ospf network point-to-multipoint
R4(config-if)#ip ospf 4 area 0
R4(config-if)#exit

Verify your configuration using the show ip ospf neighbor command:

R1#show ip ospf neighbor

Neighbor ID     Pri   State       Dead Time   Address         Interface
4.4.4.4           0   FULL/  -    00:01:59    10.0.0.4        Serial0/1
2.2.2.2           0   FULL/  -    00:01:40    10.0.0.2        Serial0/1

R2#show ip ospf neighbor

Neighbor ID     Pri   State       Dead Time   Address         Interface
1.1.1.1           0   FULL/  -    00:01:33    10.0.0.1        Serial0/1

R4#show ip ospf neighbor

Neighbor ID     Pri   State       Dead Time   Address         Interface
1.1.1.1           0   FULL/  -    00:01:40    10.0.0.1        Serial0/0

Task 4

R2(config)#interface fastethernet 0/0
R2(config-if)#ip address 192.168.0.2 255.255.255.0
R2(config-if)#ip address 192.168.1.2 255.255.255.0 secondary
R2(config-if)#ip ospf 2 area 1
R2(config-if)#exit
R4(config)#interface fastethernet 0/0
R4(config-if)#ip address 192.168.0.4 255.255.255.0        Â
R4(config-if)#ip address 192.168.1.4 255.255.255.0 secondary
R4(config-if)#ip ospf 4 area 1
R4(config-if)#exit

Verify OSPF configuration using the show ip ospf neighbor command:

R2#show ip ospf neighbor

Neighbor ID     Pri   State      Dead Time   Address      Interface
1.1.1.1           0   FULL/  -   00:01:34    10.0.0.1     Serial0/1
4.4.4.4           1   FULL/BDR   00:00:34    192.168.0.4  FastEthernet0/0

R4#show ip ospf neighbor

Neighbor ID     Pri   State       Dead Time   Address     Interface
1.1.1.1           0   FULL/  -    00:01:58    10.0.0.1    Serial0/0
2.2.2.2           1   FULL/DR     00:00:38    192.168.0.2 FastEthernet0/0

 

Finally, verify that R1 has two routes to these subnets and can ping them both:

R1#show ip route ospf
10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
O       10.0.0.2/32 [110/64] via 10.0.0.2, 00:01:03, Serial0/1
O       10.0.0.4/32 [110/64] via 10.0.0.4, 00:01:03, Serial0/1
O IA 192.168.0.0/24 [110/65] via 10.0.0.4, 00:01:03, Serial0/1
                    [110/65] via 10.0.0.2, 00:01:03, Serial0/1
O IA 192.168.1.0/24 [110/65] via 10.0.0.4, 00:01:03, Serial0/1
                    [110/65] via 10.0.0.2, 00:01:03, Serial0/1
R1#ping 192.168.0.0

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.0, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms

R1#ping 192.168.1.0

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.0, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms

Task 5

To complete this task you need to think outside the box and use the area <area> range command. This command allows you to directly specify the cost of the advertised summary route. Prior to any routing changes, R1 shows the following route entries:

R1#show ip route ospf
10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
O       10.0.0.2/32 [110/64] via 10.0.0.2, 00:01:03, Serial0/1
O       10.0.0.4/32 [110/64] via 10.0.0.4, 00:01:03, Serial0/1
O IA 192.168.0.0/24 [110/65] via 10.0.0.4, 00:01:03, Serial0/1
                    [110/65] via 10.0.0.2, 00:01:03, Serial0/1
O IA 192.168.1.0/24 [110/65] via 10.0.0.4, 00:01:03, Serial0/1
                    [110/65] via 10.0.0.2, 00:01:03, Serial0/1

This task is completed as follows:

R2(config)#router ospf 2
R2(config-router)#area 1 range 192.168.0.0 255.255.255.0 cost 1
R2(config-router)#area 1 range 192.168.1.0 255.255.255.0 cost 5
R2(config-router)#exit
R4(config)#router ospf 4
R4(config-router)#area 1 range 192.168.0.0 255.255.255.0 cost 5
R4(config-router)#area 1 range 192.168.1.0 255.255.255.0 cost 1
R4(config-router)#exit

Following this configuration, the routing table on R1 shows the following entries:

R1#show ip route ospf
10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
O       10.0.0.2/32 [110/64] via 10.0.0.2, 00:01:58, Serial0/1
O       10.0.0.4/32 [110/64] via 10.0.0.4, 00:01:58, Serial0/1
O IA 192.168.0.0/24 [110/65] via 10.0.0.2, 00:01:58, Serial0/1
O IA 192.168.1.0/24 [110/65] via 10.0.0.4, 00:01:35, Serial0/1

Task 6

The requirements of this task are two-fold. First, you must enable OSPF across the WAN link between R1 and R2 without explicitly enabling it for the 10.0.1.0/30 subnet. To do so, you should configure a GRE tunnel between the two routers. This task is completed as follows:

R1(config)#interface tunnel 0
R1(config-if)#ip address 200.0.0.1 255.255.255.252
R1(config-if)#ip ospf 1 area 5
R1(config-if)#tunnel source serial 0/0
R1(config-if)#tunnel destination 10.0.1.2
R1(config-if)#exit
R2(config)#interface tunnel 0
R2(config-if)#ip address 200.0.0.2 255.255.255.252
R2(config-if)#ip ospf 2 area 5
R2(config-if)#tunnel source serial 0/0
R2(config-if)#tunnel destination 10.0.1.1
R2(config-if)#exit

Verify your configuration using the show ip ospf neighbor command:

R1#show ip ospf neighbor

Neighbor ID     Pri   State       Dead Time   Address         Interface
4.4.4.4           0   FULL/  -    00:01:58    10.0.0.4        Serial0/1
2.2.2.2           0   FULL/  -    00:01:57    10.0.0.2        Serial0/1
2.2.2.2           0   FULL/  -    00:00:34    200.0.0.2       Tunnel0

R2#show ip ospf neighbor

Neighbor ID     Pri   State       Dead Time   Address         Interface
1.1.1.1           0   FULL/  -    00:01:54    10.0.0.1        Serial0/1
4.4.4.4           1   FULL/BDR    00:00:38    192.168.0.4     FastEthernet0/0
1.1.1.1           0   FULL/  -    00:00:32    200.0.0.1       Tunnel0

The second part of this task requires that you configure a virtual link so that when the Frame Relay WAN is down, area 1 still has a logical connection to the backbone. If you do not configure a virtual link, routing will ‘break’ when the Frame Relay WAN fails. This task is completed as follows:

R1(config)#router ospf 1
R1(config-router)#area 5 virtual-link 2.2.2.2
R1(config-router)#exit
R2(config)#router ospf 2
R2(config-router)#area 5 virtual-link 1.1.1.1
R2(config-router)#exit

Verify your configuration using the show ip ospf virtual-links command:

R1#show ip ospf virtual-links 
Virtual Link OSPF_VL0 to router 2.2.2.2 is up
Run as demand circuit
DoNotAge LSA allowed.
Transit area 5, via interface Tunnel0, Cost of using 11111
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:02
Adjacency State FULL (Hello suppressed)
Index 3/4, retransmission queue length 0, number of retransmission 0
First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
Last retransmission scan length is 0, maximum is 0
Last retransmission scan time is 0 msec, maximum is 0 msec

Finally, test your configuration by shutting down the Frame Relay interface on R1:

R1(config)#interface serial 0/1
R1(config-if)#shutdown
R1(config-if)#exit
R1(config)#do show ip route ospf
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
O       10.0.0.2/32 [110/11111] via 200.0.0.2, 00:00:03, Tunnel0
O IA 192.168.0.0/24 [110/11112] via 200.0.0.2, 00:00:03, Tunnel0
O IA 192.168.1.0/24 [110/11116] via 200.0.0.2, 00:00:03, Tunnel0

Final Router Configurations

R1

 

R1#term len 0
R1#sh run
Building configuration…

Current configuration : 1260 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface Tunnel0
ip address 200.0.0.1 255.255.255.252
ip ospf 1 area 5
tunnel source Serial0/0
tunnel destination 10.0.1.2
!
interface FastEthernet0/0
ip address 150.1.1.1 255.255.255.0
ip ospf 1 area 0
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.1.1 255.255.255.252
clock rate 2000000
!
interface Serial0/1
ip address 10.0.0.1 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-multipoint
ip ospf 1 area 0
frame-relay map ip 10.0.0.2 102 broadcast
frame-relay map ip 10.0.0.4 104 broadcast
!
router ospf 1
router-id 1.1.1.1
log-adjacency-changes
area 5 virtual-link 2.2.2.2
passive-interface FastEthernet0/0
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R1#

R2

 

R2#term len 0
R2#sh run
Building configuration…

Current configuration : 1339 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface Tunnel0
ip address 200.0.0.2 255.255.255.252
ip ospf 2 area 5
tunnel source Serial0/0
tunnel destination 10.0.1.1
!
interface FastEthernet0/0
ip address 192.168.1.2 255.255.255.0 secondary
ip address 192.168.0.2 255.255.255.0
ip ospf 2 area 1
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.1.2 255.255.255.252
!
interface Serial0/1
ip address 10.0.0.2 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-multipoint
ip ospf 2 area 0
frame-relay map ip 10.0.0.1 201 broadcast
frame-relay map ip 10.0.0.4 201
!
router ospf 2
router-id 2.2.2.2
log-adjacency-changes
area 1 range 192.168.0.0 255.255.255.0 cost 1
area 1 range 192.168.1.0 255.255.255.0 cost 5
area 5 virtual-link 1.1.1.1
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R2#

R3

 

R3-Frame-Relay-Switch#term len 0
R3-Frame-Relay-Switch#sh run
Building configuration…

Current configuration : 1556 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R3-Frame-Relay-Switch
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
frame-relay switching
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial1/0
description ‘Connected To R1 Serial 0/1’
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay intf-type dce
frame-relay route 102 interface Serial1/1 201
frame-relay route 104 interface Serial1/2 401
!
interface Serial1/1
description ‘Connected To R2 Serial 0/1’
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay intf-type dce
frame-relay route 201 interface Serial1/0 102
!
interface Serial1/2
description ‘Connected To R4 Serial 0/0’
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay intf-type dce
frame-relay route 401 interface Serial1/0 104
!
interface Serial1/3
no ip address
shutdown
!
interface Serial1/4
no ip address
shutdown
!
interface Serial1/5
no ip address
shutdown
!
interface Serial1/6
no ip address
shutdown
!
interface Serial1/7
no ip address
shutdown
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R3-Frame-Relay-Switch#

R4

 

R4#term len 0
R4#sh run
Building configuration…

Current configuration : 1168 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R4
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 192.168.1.4 255.255.255.0 secondary
ip address 192.168.0.4 255.255.255.0
ip ospf 4 area 1
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.4 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-multipoint
ip ospf 4 area 0
frame-relay map ip 10.0.0.1 401 broadcast
frame-relay map ip 10.0.0.2 401
!
interface Serial0/1
no ip address
shutdown
!
router ospf 4
router-id 4.4.4.4
log-adjacency-changes
area 1 range 192.168.0.0 255.255.255.0 cost 5
area 1 range 192.168.1.0 255.255.255.0 cost 1
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R4#

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.