www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNP Labs Solutions / CCNP Lab 038 Solution: Border Gateway Protocol Lab

CCNP Lab 038 Solution: Border Gateway Protocol Lab

Lab Objective:

The focus of this lab is to understand BGP implementation and configuration in Cisco IOS routers. Additional technologies include route filtering and path control.

Lab Topology:

The lab network topology is illustrated below:

department638

 

IMPORTANT NOTE

If you are using the www.howtonetwork.net racks, please bring up the LAN interfaces connected to the routers by issuing the no shutdown command on the connected switches. If you are using a home lab with no
Switches, you can bring up the LAN interfaces using the following configurations on your routers:

interface fastethernet 0/0
 no keepalive
 loopback
 no shutdown

Alternately, you can simply connect the interfaces to a hub or switch if you have one available in your own lab.

 

Task 1

Configure hostnames and IP addressing on all routers as illustrated in the network topology.

Task 2

Configure BGP as illustrated in the topology. R1 will peer with R2. R2 will peer with R1 and R3. R3 will peer with R4. Do NOT peer R1 and R4 even though they exist in the same AS. Verify the configuration using the appropriate commands.

Task 3

Advertise the 150.2.2.0/24 and 150.3.3.0/24 prefixes connected to R2 and R3, respectively, using BGP. Do NOT advertise the 150.1.1.0/24 subnet connected to R1 and R4. However, ensure that both R2 and R3 can still ping this subnet. You are NOT allowed to use static routes. Verify your configuration using an extended ping from the LAN subnets connected to R2 and R3 to the 150.1.1.0/24 subnet connected to R1 and R4.

Task 4

Configure BGP so that R3 prefers the path via R2 to reach the 150.1.1.0/24 subnet. You are only allowed to configure a device in AS 1. You are NOT allowed to advertise the 150.1.1.0/24 prefix when completing this task. Verify your configuration and ensure that R2 and R3 can still ping the 150.1.1.1/24 and 150.1.1.4/24 addresses when complete. Use an extended ping that is sourced from R3s LAN IP address.
Task 5

Configure OSPF on the LAN subnet between R1 and R4. Next, configure AS 1 so that R4 will prefer the path via R1 to reach the 150.2.2.0/24 or 150.3.3.0/24 subnets. In the event that the WAN link between R1 and R2 is down, the path via R4 should be used instead. You are NOT allowed to establish an iBGP neighbor relationship between R1 and R4 to complete this task. Additionally, you are not allowed to use the distance command to modify any protocol administrative distance values. Instead, use a BGP feature when completing this task. Verify your configuration using the appropriate commands. Ensure R4 can still ping the 150.2.2.0/24 and the 150.3.3.0/24 subnets when complete.

HINT: Use the BGP network command to complete this task.

Lab Validation

Task 1

Please refer to previous labs for basic IP addressing and hostname configuration. This will not be included in this section to avoid being redundant.

Task 2

R1(config)#router bgp 1
R1(config-router)#bgp router-id 1.1.1.1
R1(config-router)#neighbor 10.0.0.2 remote-as 2
R1(config-router)#exit
R2(config)#router bgp 2
R2(config-router)#bgp router-id 2.2.2.2
R2(config-router)#neighbor 10.0.0.1 remote-as 1
R2(config-router)#neighbor 10.0.0.10 remote-as 3
R2(config-router)#exit
R3(config)#router bgp 3
R3(config-router)#bgp router-id 3.3.3.3
R3(config-router)#neighbor 10.0.0.9 remote-as 2
R3(config-router)#neighbor 10.0.0.14 remote-as 1
R3(config-router)#exit
R4(config)#router bgp 1
R4(config-router)#bgp router-id 4.4.4.4
R4(config-router)#neighbor 10.0.0.13 remote-as 3
R4(config-router)#exit

 

Verify your configuration using the show ip bgp summary command:

R1#show ip bgp summary
BGP router identifier 1.1.1.1, local AS number 1
BGP table version is 1, main routing table version 1

Neighbor    V    AS MsgRcvd MsgSent   TblVer  InQ OutQ Up/Down  State/PfxRcd
10.0.0.2    4     2       7       7        1    0    0 00:05:00        0

R2#show ip bgp summary
BGP router identifier 2.2.2.2, local AS number 2
BGP table version is 1, main routing table version 1

Neighbor    V    AS MsgRcvd MsgSent   TblVer  InQ OutQ Up/Down  State/PfxRcd
10.0.0.1    4     1       8       8        1    0    0 00:05:03        0
10.0.0.10   4     3       6       7        1    0    0 00:03:31        0

R3#show ip bgp summary
BGP router identifier 3.3.3.3, local AS number 3
BGP table version is 1, main routing table version 1

Neighbor    V    AS MsgRcvd MsgSent   TblVer  InQ OutQ Up/Down  State/PfxRcd
10.0.0.9    4     2       7       6        1    0    0 00:03:35        0
10.0.0.14   4     1       6       6        1    0    0 00:02:41        0

R4#show ip bgp summary
BGP router identifier 4.4.4.4, local AS number 1
BGP table version is 1, main routing table version 1

Neighbor    V    AS MsgRcvd MsgSent   TblVer  InQ OutQ Up/Down  State/PfxRcd
10.0.0.13   4     3       6       6        1    0    0 00:02:30        0

Task 3

To complete this task, you need to configure R1 and R4 to advertise defaults to R2 and R3:

R2(config)#router bgp 2
R2(config-router)#network 150.2.2.0 mask 255.255.255.0
R2(config-router)#exit
R3(config)#router bgp 3
R3(config-router)#network 150.3.3.0 mask 255.255.255.0
R3(config-router)#exit
R1(config)#router bgp 1
R1(config-router)#neighbor 10.0.0.2 default-originate
R1(config-router)#exit
R4(config)#router bgp 1
R4(config-router)#neighbor 10.0.0.13 default-originate
R4(config-router)#exit

Next, verify your configuration using the show ip bgp command:

R1#show ip bgp
BGP table version is 3, local router ID is 1.1.1.1
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale
Origin codes: i – IGP, e – EGP, ? – incomplete

Network          Next Hop            Metric LocPrf Weight Path
*> 150.2.2.0/24     10.0.0.2                 0             0 2 i
*> 150.3.3.0/24     10.0.0.2                               0 2 3 i

R2#show ip bgp
BGP table version is 4, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale
Origin codes: i – IGP, e – EGP, ? – incomplete

Network          Next Hop            Metric LocPrf Weight Path
*  0.0.0.0          10.0.0.10                              0 3 1 i
*>                  10.0.0.1                 0             0 1 i
*> 150.2.2.0/24     0.0.0.0                  0         32768 i
*> 150.3.3.0/24     10.0.0.10                0             0 3 i

R3#show ip bgp
BGP table version is 5, local router ID is 3.3.3.3
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale
Origin codes: i – IGP, e – EGP, ? – incomplete

Network          Next Hop            Metric LocPrf Weight Path
*> 0.0.0.0          10.0.0.14                0             0 1 i
*                   10.0.0.9                               0 2 1 i
*> 150.2.2.0/24     10.0.0.9                 0             0 2 i
*> 150.3.3.0/24     0.0.0.0                  0         32768 i

R4#show ip bgp
BGP table version is 3, local router ID is 4.4.4.4
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale
Origin codes: i – IGP, e – EGP, ? – incomplete

Network          Next Hop            Metric LocPrf Weight Path
*> 150.2.2.0/24     10.0.0.13                              0 3 2 i
*> 150.3.3.0/24     10.0.0.13                0             0 3 i

 

Finally, verify that R2 and R3 can ping the 150.1.1.1/24 and 150.1.1.4/24 addresses from their respective LAN addresses using an extended ping:

R2#ping 150.1.1.1 source fastethernet 0/0 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 150.2.2.2
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms

R2#ping 150.1.1.4 source fastethernet 0/0 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.1.1.4, timeout is 2 seconds:
Packet sent with a source address of 150.2.2.2
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 16/16/20 ms

R3#ping 150.1.1.1 source fastethernet 0/0 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 150.3.3.3
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 16/16/20 ms

R3#ping 150.1.1.4 source fastethernet 0/0 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.1.1.4, timeout is 2 seconds:
Packet sent with a source address of 150.3.3.3
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 16/16/16 ms

Task 4

To complete this task, you need to use a route map and AS_PATH prepending to make the default route advertised by R4 longer than that advertised by R1. This route-map should be applied to the default route advertised to R3. This task is completed as follows:

R4(config)#route-map PREPEND permit 10
R4(config-route-map)#set as-path prepend 1 1 1 1
R4(config-route-map)#exit
R4(config)#router bgp 1
R4(config-router)#neighbor 10.0.0.13 default-originate route-map PREPEND
R4(config-router)#exit

Following this change, verify the BGP Table on R3 to ensure the preferred default is via R2:

R3#show ip bgp
BGP table version is 6, local router ID is 3.3.3.3
Status codes: s suppressed, d damped, h history, * valid, > best, i – internal,
r RIB-failure, S Stale
Origin codes: i – IGP, e – EGP, ? – incomplete

Network          Next Hop            Metric LocPrf Weight Path
*  0.0.0.0          10.0.0.14                0             0 1 1 1 1 1 i
*>                  10.0.0.9                               0 2 1 i
*> 150.2.2.0/24     10.0.0.9                 0             0 2 i
*> 150.3.3.0/24     0.0.0.0                  0         32768 i

Finally, verify that R3 can still ping the 150.1.1.1/24 and 150.1.1.4/24 addresses after the change:

R3#ping 150.1.1.1 source fastethernet 0/0 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 150.3.3.3
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 16/18/28 ms

R3#ping 150.1.1.4 source fastethernet 0/0 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.1.1.4, timeout is 2 seconds:
Packet sent with a source address of 150.3.3.3
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 16/16/16 ms

Task 5

The requirements of this task are threefold. First, you need to enable OSPF between R1 and R4 across their directly connected LAN segment. Following this configuration, verify the OSPF adjacency between the routers using the show ip ospf neighbor command. You can refer to previous labs for OSPF configuration basics.

R1#show ip ospf neighbor

Neighbor ID  Pri   State     Dead Time   Address         Interface
4.4.4.4        1   FULL/BDR  00:00:37    150.1.1.4       FastEthernet0/0

R4#show ip ospf neighbor

Neighbor ID  Pri   State     Dead Time   Address         Interface
1.1.1.1        1   FULL/DR   00:00:39    150.1.1.1       FastEthernet0/0

The second part of this task entails redistribution between OSPF and BGP. This allows the LAN subnets connected to R2 and R4 to be advertised across the LAN link connecting R1 and R2. You do NOT need to redistribute OSPF routes into BGP, otherwise you will advertise the LAN subnet between R1 and R4, which is NOT permitted as stated in previous tasks:

R1(config)#router ospf 1
R1(config-router)#redistribute bgp 1 subnets
R1(config-router)#exit
R4(config)#router ospf 4
R4(config-router)#redistribute bgp 1 subnets
R4(config-router)#exit

Following this configuration, verify that the routing tables on both routers show all routes:

R1#show ip route
Codes: C – connected, S – static, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2
i – IS-IS, su – IS-IS summary, L1 – IS-IS level-1, L2 – IS-IS level-2
ia – IS-IS inter area, * – candidate default, U – per-user static route
o – ODR, P – periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 1 subnets
C       10.0.0.0 is directly connected, Serial0/0
150.1.0.0/24 is subnetted, 1 subnets
C       150.1.1.0 is directly connected, FastEthernet0/0
150.2.0.0/24 is subnetted, 1 subnets
B       150.2.2.0 [20/0] via 10.0.0.2, 00:28:43
150.3.0.0/24 is subnetted, 1 subnets
B       150.3.3.0 [20/0] via 10.0.0.2, 00:29:14

R4#show ip route
Codes: C – connected, S – static, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2
i – IS-IS, su – IS-IS summary, L1 – IS-IS level-1, L2 – IS-IS level-2
ia – IS-IS inter area, * – candidate default, U – per-user static route
o – ODR, P – periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 1 subnets
C       10.0.0.12 is directly connected, Serial0/0
150.1.0.0/24 is subnetted, 1 subnets
C       150.1.1.0 is directly connected, FastEthernet0/0
150.2.0.0/24 is subnetted, 1 subnets
B       150.2.2.0 [20/0] via 10.0.0.13, 00:07:07
150.3.0.0/24 is subnetted, 1 subnets
B       150.3.3.0 [20/0] via 10.0.0.13, 00:29:10

As illustrated in the output above, both routers prefer the BGP routes because of the lower administrative distance of external BGP (20) versus OSPF (110). To complete this task, use the hint provided in the lab, which states that you should use the BGP network command.

The correct command to use in this case would be network <address> <mask> backdoor command. The backdoor keyword configures the router to change the administrative distance of the specified external BGP route from 20 to 200. This allows IGP routes to be preferred instead. When the IGP routes are no longer present in the routing table, the BGP route is again used. This task is completed as follows:

R4(config)#router bgp 1
R4(config-router)#network 150.2.2.0 mask 255.255.255.0 backdoor
R4(config-router)#network 150.3.3.0 mask 255.255.255.0 backdoor
R4(config-router)#exit

Following this change, the routing table on R4 shows the following route entries:

R4#show ip route
Codes: C – connected, S – static, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2
i – IS-IS, su – IS-IS summary, L1 – IS-IS level-1, L2 – IS-IS level-2
ia – IS-IS inter area, * – candidate default, U – per-user static route
o – ODR, P – periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 1 subnets
C       10.0.0.12 is directly connected, Serial0/0
150.1.0.0/24 is subnetted, 1 subnets
C       150.1.1.0 is directly connected, FastEthernet0/0
150.2.0.0/24 is subnetted, 1 subnets
O E2    150.2.2.0 [110/1] via 150.1.1.1, 00:00:43, FastEthernet0/0
150.3.0.0/24 is subnetted, 1 subnets
O E2    150.3.3.0 [110/1] via 150.1.1.1, 00:00:35, FastEthernet0/0

Next, complete this task by ensuring that R4 can still ping the 150.2.2.0/24 and the 150.3.3.0/24 subnets when complete. Because the routes are known via the FastEthernet0/0 interface, you do NOT need to use an extended ping as the ping will be sourced from the egress interface:

R4#ping 150.2.2.2 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.2.2.2, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 1/3/4 ms

R4#ping 150.3.3.3 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.3.3.3, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 16/17/20 ms

Finally, verify redundancy by shutting down the R1-R2 link and ensuring that R1 can still reach the 150.2.2.0/24 and 150.3.3.0/24 subnets. This is completed as follows:

R1(config)#interface serial 0/0
R1(config-if)#shutdown
R1(config-if)#exit
R1(config)#do show ip route
Codes: C – connected, S – static, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2
i – IS-IS, su – IS-IS summary, L1 – IS-IS level-1, L2 – IS-IS level-2
ia – IS-IS inter area, * – candidate default, U – per-user static route
o – ODR, P – periodic downloaded static route

Gateway of last resort is not set

150.1.0.0/24 is subnetted, 1 subnets
C       150.1.1.0 is directly connected, FastEthernet0/0
150.2.0.0/24 is subnetted, 1 subnets
O E2    150.2.2.0 [110/1] via 150.1.1.4, 00:00:08, FastEthernet0/0
150.3.0.0/24 is subnetted, 1 subnets
O E2    150.3.3.0 [110/1] via 150.1.1.4, 00:00:08, FastEthernet0/0
R1(config)#
R1(config)#do ping 150.2.2.2 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.2.2.2, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 28/30/32 ms
R1(config)#
R1(config)#do ping 150.3.3.3 repeat 10

Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 150.3.3.3, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 16/16/16 ms

Final Router Configurations

R1

 

R1#term len 0
R1#sh run
Building configuration…

Current configuration : 1135 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.1.1.1 255.255.255.0
ip ospf 1 area 0
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.1 255.255.255.252
shutdown
clock rate 2000000
!
interface Serial0/1
no ip address
shutdown
!
router ospf 21
log-adjacency-changes
!
router ospf 1
router-id 1.1.1.1
log-adjacency-changes
redistribute bgp 1 subnets
!
router bgp 1
no synchronization
bgp router-id 1.1.1.1
bgp log-neighbor-changes
neighbor 10.0.0.2 remote-as 2
neighbor 10.0.0.2 default-originate
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R1#

R2

 

R2#term len 0
R2#sh run
Building configuration…

Current configuration : 1006 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.2.2.2 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.2 255.255.255.252
!
interface Serial0/1
ip address 10.0.0.9 255.255.255.252
!
router bgp 2
no synchronization
bgp router-id 2.2.2.2
bgp log-neighbor-changes
network 150.2.2.0 mask 255.255.255.0
neighbor 10.0.0.1 remote-as 1
neighbor 10.0.0.10 remote-as 3
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R2#

 

R3

 

R3#term len 0
R3#sh run
Building configuration…

Current configuration : 1347 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R3
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.3.3.3 255.255.255.0
duplex auto
speed auto
!
interface Serial1/0
no ip address
shutdown
clock rate 128000
!
interface Serial1/1
ip address 10.0.0.10 255.255.255.252
clock rate 128000
!
interface Serial1/2
ip address 10.0.0.13 255.255.255.252
clock rate 128000
!
interface Serial1/3
no ip address
shutdown
!
interface Serial1/4
no ip address
shutdown
!
interface Serial1/5
no ip address
shutdown
!
interface Serial1/6
no ip address
shutdown
!
interface Serial1/7
no ip address
shutdown
!
router bgp 3
no synchronization
bgp router-id 3.3.3.3
bgp log-neighbor-changes
network 150.3.3.0 mask 255.255.255.0
neighbor 10.0.0.9 remote-as 2
neighbor 10.0.0.14 remote-as 1
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R3#

R4

 

R4#term len 0
R4#sh run
Building configuration…

Current configuration : 1239 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R4
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.1.1.4 255.255.255.0
ip ospf 4 area 0
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.14 255.255.255.252
!
interface Serial0/1
no ip address
shutdown
!
router ospf 4
router-id 4.4.4.4
log-adjacency-changes
redistribute bgp 1 subnets
!
router bgp 1
no synchronization
bgp router-id 4.4.4.4
bgp log-neighbor-changes
network 150.2.2.0 mask 255.255.255.0 backdoor
network 150.3.3.0 mask 255.255.255.0 backdoor
neighbor 10.0.0.13 remote-as 3
neighbor 10.0.0.13 default-originate route-map PREPEND
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
route-map PREPEND permit 10
set as-path prepend 1 1 1 1
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R4#

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.