www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNP Labs Solutions / CCNP Lab 071 Solution: Multicast – PIM Dense Mode Lab

CCNP Lab 071 Solution: Multicast – PIM Dense Mode Lab

Lab Objective:

The focus of this lab is to understand IP Multicast Dense Mode forwarding in Cisco IOS routers. Additional technologies include Internet Group Management Protocol (IGMP).

Lab Topology:

The lab network topology is illustrated below:

department671

 

IMPORTANT NOTE

If you are using the www.howtonetwork.net racks, please bring up the LAN interfaces connected to the routers by issuing the no shutdown command on the connected switches. If you are using a home lab with no
Switches, you can bring up the LAN interfaces using the following configurations on your routers:

interface fastethernet 0/0
no keepalive
loopback
no shutdown

Alternately, you can simply connect the interfaces to a hub or switch if you have one available in your own lab.

 

Task 1

Configure the hostnames, IP addressing on all routers as illustrated in the network topology.

Task 2

Enable EIGRP on all routers as illustrated in the topology. Verify your EIGRP configuration.

Task 3

Enable Internet Group Management Protocol on the LAN interfaces of R1 and R4. Ensure that the configuration allows the host to request traffic from a specific host in the network. Next, enable Dense Mode forwarding on the interfaces. Verify your solution using the appropriate commands.

Task 4

Enable Dense Mode forwarding on all router WAN interfaces. Verify your configuration using the appropriate commands.

 

 

Task 5

Configure R1 so that its LAN interface is joined to Multicast group 227.1.1.1. Configure R4 so that its LAN interface is joined to Multicast group 227.4.4.4. Verify that R1 can ping R4s Multicast group and that R4 can ping R1s Multicast group.

 

Lab Validation

Task 1

Please refer to previous tasks for basic VLAN and IP addressing configuration. These will not be included in this section for brevity and to avoid being redundant.

Task 2

Please refer to previous labs for basic EIGRP configuration. Following this, verify your EIGRP configuration using the show ip eigrp neighbors andshow ip route commands. Following this configuration, your route tables should show the following route information:

R1#show ip route eigrp
10.0.0.0/30 is subnetted, 3 subnets
D 10.0.0.8 [90/2681856] via 10.0.0.2, 00:00:12, Serial0/0
D 10.0.0.12 [90/21536000] via 10.0.0.2, 00:00:12, Serial0/0
150.4.0.0/24 is subnetted, 1 subnets
D 150.4.4.0 [90/21538560] via 10.0.0.2, 00:00:12, Serial0/0
R2#show ip route eigrp
10.0.0.0/30 is subnetted, 3 subnets
D 10.0.0.12 [90/21024000] via 10.0.0.10, 00:00:22, Serial0/1
150.1.0.0/24 is subnetted, 1 subnets
D 150.1.1.0 [90/2172416] via 10.0.0.1, 00:00:17, Serial0/0
150.4.0.0/24 is subnetted, 1 subnets
D 150.4.4.0 [90/21026560] via 10.0.0.10, 00:00:22, Serial0/1
R3#show ip route eigrp
10.0.0.0/30 is subnetted, 3 subnets
D 10.0.0.0 [90/21024000] via 10.0.0.9, 00:00:25, Serial1/1
150.1.0.0/24 is subnetted, 1 subnets
D 150.1.1.0 [90/21026560] via 10.0.0.9, 00:00:20, Serial1/1
150.4.0.0/24 is subnetted, 1 subnets
D 150.4.4.0 [90/20514560] via 10.0.0.14, 00:00:31, Serial1/2
R4#show ip route eigrp
10.0.0.0/30 is subnetted, 3 subnets
D 10.0.0.8 [90/21024000] via 10.0.0.13, 00:00:34, Serial0/0
D 10.0.0.0 [90/21536000] via 10.0.0.13, 00:00:28, Serial0/0
150.1.0.0/24 is subnetted, 1 subnets
D 150.1.1.0 [90/21538560] via 10.0.0.13, 00:00:23, Serial0/0

Task 3

The core requirement of this task is straightforward. However, in order to complete this task as required you need to understand, from the wording, what version of IGMP is required. Specifically, the task is requiring that IGMPv3 be enabled. IGMP version 3, the most recent modification of the IGMP specification, is defined in RFC 3376. This version now allows the host to request traffic from a specific host in the network. Hosts can also specify a list of sources that they should not receive Multicast traffic from. These changes provide support for the use of Source Specific Multicast within the 232.0.0.0 /8 Multicast group address range. Given this understanding, this task is completed as follows:

R1(config)#ip multicast-routing
R1(config)#interface fastethernet 0/0
R1(config-if)#ip igmp version 3
R1(config-if)#ip pim dense-mode
R1(config-if)#exit
R4(config)#ip multicast-routing
R4(config)#interface fastethernet 0/0
R4(config-if)#ip igmp version 3
R4(config-if)#ip pim dense-mode
R4(config-if)#exit

Next, verify your configuration using the show ip igmp interface command:

R1#show ip igmp interface fastethernet 0/0
FastEthernet0/0 is up, line protocol is up
Internet address is 150.1.1.1/24
IGMP is enabled on interface
Current IGMP host version is 3
Current IGMP router version is 3
IGMP query interval is 60 seconds
IGMP querier timeout is 120 seconds
IGMP max query response time is 10 seconds
Last member query count is 2
Last member query response interval is 1000 ms
Inbound IGMP access group is not set
IGMP activity: 1 joins, 0 leaves
Multicast routing is enabled on interface
Multicast TTL threshold is 0
Multicast designated router (DR) is 150.1.1.1 (this system)
IGMP querying router is 150.1.1.1 (this system)
Multicast groups joined by this system (number of users):
224.0.1.40(1)
R4#show ip igmp interface fastethernet 0/0 
FastEthernet0/0 is up, line protocol is up
Internet address is 150.4.4.4/24
IGMP is enabled on interface
Current IGMP host version is 3
Current IGMP router version is 3
IGMP query interval is 60 seconds
IGMP querier timeout is 120 seconds
IGMP max query response time is 10 seconds
Last member query count is 2
Last member query response interval is 1000 ms
Inbound IGMP access group is not set
IGMP activity: 1 joins, 0 leaves
Multicast routing is enabled on interface
Multicast TTL threshold is 0
Multicast designated router (DR) is 150.4.4.4 (this system)
IGMP querying router is 150.1.1.1
Multicast groups joined by this system (number of users):
224.0.1.40(1)

Notice in the last line of the output that the interface is automatically joined to group 224.0.1.40. This group is for Cisco RP Discovery messages. The interface is automatically joined to this group because Dense mode assumes that all hosts wants to receive Multicast traffic, unless they explicitly state that they do not. This group is enabled by default; however, it is not applicable in this section because there is no RP when PIM dense mode is enabled. It simply indicates that the interface is listening for packets that may be sent to this group address.

Task 4

The requirements of this task are straightforward. This task is completed as follows:

R1(config)#interface serial 0/0
R1(config-if)#ip pim dense-mode
R1(config-if)#exit
R2(config)#ip multicast-routing
R2(config)#interface serial 0/0
R2(config-if)#ip pim dense-mode
R2(config-if)#exit
R2(config)#interface serial 0/1
R2(config-if)#ip pim dense-mode
R2(config-if)#exit
R3(config)#ip multicast-routing
R3(config)#interface serial 1/1
R3(config-if)#ip pim dense-mode
R3(config-if)#exit
R3(config)#interface serial 1/2
R3(config-if)#ip pim dense-mode
R3(config-if)#exit
R4(config)#interface serial 0/0
R4(config-if)#ip pim dense-mode
R4(config-if)#exit

Next, verify PIM Dense Mode parameters using the show ip pim interface command:

R4#show ip pim interface serial 0/0 detail
Serial0/0 is up, line protocol is up
Internet address is 10.0.0.14/30
Multicast switching: fast
Multicast packets in/out: 254/0
Multicast TTL threshold: 0
PIM: enabled
PIM version: 2, mode: dense
PIM DR: 0.0.0.0
PIM neighbor count: 1
PIM Hello/Query interval: 30 seconds
PIM Hello packets in/out: 4/5
PIM State-Refresh processing: enabled
PIM State-Refresh origination: disabled
PIM NBMA mode: disabled
PIM ATM multipoint signalling: disabled
PIM domain border: disabled
Multicast Tagswitching: disabled

Task 5

To configure a router interface to join a Multicast group, a technique commonly used to test the Multicast configuration, use the ip igmp join-group <group> interface command:

R1(config)#interface fastethernet 0/0
R1(config-if)#ip igmp join-group 227.1.1.1
R1(config-if)#exit
R4(config)#interface fastethernet 0/0
R4(config-if)#ip igmp join-group 227.4.4.4
R4(config-if)#exit

Next, verify your configuration using the show ip igmp interface command:

R1#show ip igmp interface fastethernet 0/0
FastEthernet0/0 is up, line protocol is up
Internet address is 150.1.1.1/24
IGMP is enabled on interface
Current IGMP host version is 3
Current IGMP router version is 3
IGMP query interval is 60 seconds
IGMP querier timeout is 120 seconds
IGMP max query response time is 10 seconds
Last member query count is 2
Last member query response interval is 1000 ms
Inbound IGMP access group is not set
IGMP activity: 3 joins, 0 leaves
Multicast routing is enabled on interface
Multicast TTL threshold is 0
Multicast designated router (DR) is 150.4.4.4
IGMP querying router is 150.1.1.1 (this system)
Multicast groups joined by this system (number of users):
224.0.1.40(1) 227.1.1.1(1)
R4#show ip igmp interface fastethernet 0/0
FastEthernet0/0 is up, line protocol is up
Internet address is 150.4.4.4/24
IGMP is enabled on interface
Current IGMP host version is 3
Current IGMP router version is 3
IGMP query interval is 60 seconds
IGMP querier timeout is 120 seconds
IGMP max query response time is 10 seconds
Last member query count is 2
Last member query response interval is 1000 ms
Inbound IGMP access group is not set
IGMP activity: 2 joins, 0 leaves
Multicast routing is enabled on interface
Multicast TTL threshold is 0
Multicast designated router (DR) is 150.4.4.4 (this system)
IGMP querying router is 150.1.1.1
Multicast groups joined by this system (number of users):
224.0.1.40(1) 227.4.4.4(1)

Finally, complete the task by pinging the Multicast groups from routers R1 and R4:

R1#ping 227.4.4.4

Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 227.4.4.4, timeout is 2 seconds:

Reply to request 0 from 10.0.0.14, 40 ms

R4#ping 227.1.1.1

Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 227.1.1.1, timeout is 2 seconds:

Reply to request 0 from 10.0.0.1, 40 ms

Final Router Configurations

R1

 

R1#term len 0
R1#sh run
Building configuration…

Current configuration : 986 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip multicast-routing
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.1.1.1 255.255.255.0
ip pim dense-mode
ip igmp join-group 227.1.1.1
ip igmp version 3
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.1 255.255.255.252
ip pim dense-mode
clock rate 2000000
!
interface Serial0/1
no ip address
!
router eigrp 254
network 0.0.0.0
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R1#

R2

 

R2#term len 0
R2#sh run
Building configuration…

Current configuration : 906 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip multicast-routing
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.2 255.255.255.252
ip pim dense-mode
!
interface Serial0/1
ip address 10.0.0.9 255.255.255.252
ip pim dense-mode
!
router eigrp 254
network 0.0.0.0
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R2#

R3

 

R3#term len 0
R3#sh run
Building configuration…

Current configuration : 1247 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R3
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip multicast-routing
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial1/0
no ip address
shutdown
clock rate 128000
!
interface Serial1/1
ip address 10.0.0.10 255.255.255.252
ip pim dense-mode
clock rate 128000
!
interface Serial1/2
ip address 10.0.0.13 255.255.255.252
ip pim dense-mode
clock rate 128000
!
interface Serial1/3
no ip address
shutdown
!
interface Serial1/4
no ip address
shutdown
!
interface Serial1/5
no ip address
shutdown
!
interface Serial1/6
no ip address
shutdown
!
interface Serial1/7
no ip address
shutdown
!
router eigrp 254
network 0.0.0.0
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R3#

R4

 

R4#term len 0
R4#sh run
Building configuration…

Current configuration : 955 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R4
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
no ip domain lookup
ip multicast-routing
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 150.4.4.4 255.255.255.0
ip pim dense-mode
ip igmp join-group 227.4.4.4
ip igmp version 3
duplex auto
speed auto
!
interface Serial0/0
ip address 10.0.0.14 255.255.255.252
ip pim dense-mode
!
interface Serial0/1
no ip address
shutdown
!
router eigrp 254
network 0.0.0.0
no auto-summary
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end

R4#

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.