www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNP LABS / CCNP Lab 013: EIGRP Multi-Technology Lab

CCNP Lab 013: EIGRP Multi-Technology Lab

Lab Objective:

The focus of this lab is to understand EIGRP implementation and configuration in Cisco IOS routers. Additional technologies tested include summarization and authentication.

Lab Topology:

The lab network topology is illustrated below:

department613

 

IMPORTANT NOTE

If you are using the www.howtonetwork.net racks, please bring up the LAN interfaces connected to the routers by issuing the no shutdown command on the connected switches. If you are using a home lab with no
Switches, you can bring up the LAN interfaces using the following configurations on your routers:

interface fastethernet 0/0
no keepalive
loopback
no shutdown

Alternately, you can simply connect the interfaces to a hub or switch if you have one available in your own lab.

 

Task 1

Configure hostnames and IP addressing on all routers as illustrated in the network topology.

Task 2

Configure EIGRP for AS 1 as illustrated in the topology. However, do NOT advertise the 150.2.2.0/24 and 150.3.3.0/24 subnets connected to R2 and R3 via EIGRP. Additionally, authenticate EIGRP protocol updates using the password ‘CCNP’.

Task 3

Configure routers R2 and R3 to advertise ONLY the default route to R1 and R4. Ensure that R2 and R3 can ping each others’ 150.x.x.x/24 subnets. Verify that R1 and R4 can reach the 150.2.2.0/24 and 150.3.3.0/24 subnets even if their own WAN links are down or unavailable.

Task 4

Configure the following secondary subnets on the LAN segment between R1 and R4:

  1. Network: 192.168.0.0/24 – Assign 192.168.0.1/24 to R1 and 192.168.0.4/24 to R4
  2. Network: 192.168.1.0/24 – Assign 192.168.1.1/24 to R1 and 192.168.1.4/24 to R4
  3. Network: 192.168.2.0/24 – Assign 192.168.2.1/24 to R1 and 192.168.2.4/24 to R4
  4. Network: 192.168.3.0/24 – Assign 192.168.3.1/24 to R1 and 192.168.3.4/24 to R4

 

Next, configure R1 and R4 to advertise only a single route for these subnets to R2 and R3.
Task 5

Management has decided that packets sourced from the LAN interface of R2 (150.2.2.2) should use the R2-R3-R4 path to reach the 150.1.1.0/24 and 192.168.1.0/24 subnets. This should be completed without performing any modifications on any other router except for R2. Verify your configuration using the appropriate commands. Corporate IT policy states that NO static routes are allowed. Complete this solution while adhering to this policy.

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.