www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / 101 CCNP LABS / CCNP Lab 057: Cisco IOS PBR, SLA and EOT Lab

CCNP Lab 057: Cisco IOS PBR, SLA and EOT Lab

Lab Objective:

The focus of this lab is to understand PBR implementation and configuration in Cisco IOS routers. Additional technologies include IP SLA Operations and Enhanced Object Tracking.

Lab Topology:

The lab network topology is illustrated below:

department657

 

IMPORTANT NOTE

If you are using the www.howtonetwork.net racks, please bring up the LAN interfaces connected to the routers by issuing the no shutdown command on the connected switches. If you are using a home lab with no
Switches, you can bring up the LAN interfaces using the following configurations on your routers:

interface fastethernet 0/0
no keepalive
loopback
no shutdown

Alternately, you can simply connect the interfaces to a hub or switch if you have one available in your own lab.

 

Task 1

Configure hostnames, IP addressing on all routers as illustrated in the network topology. In addition, configure a Loopback 0 interface on R1 with the IP address 1.1.1.1/32.

Task 2

Configure EIGRP as illustrated in the topology. Ensure that no EIGRP packets are sent out of the LAN interfaces of R2 and R3. Do NOT enable EIGRP for the R2-R3 link. Ensure that R1 advertises a default route to R4. Next, configure static default routes on R2 and R3 as follows:

  1. R2 should have a default static route pointing to R3
  2. R3 should have a default static route pointing to R2

 

Verify your configuration using the appropriate commands on all routers in the network.

Task 3

Configure IOS PBR on R1 so that when R1 loses the EIGRP route to the 150.2.2.0/24 subnet, all traffic sourced from the 150.1.1.0/24 subnet to this destination is sent via R3. In addition to this, configure IOS PBR on R1 so that when R1 loses the EIGRP route to the 150.3.3.0/24 subnet, all traffic sourced from the 150.1.1.0/24 subnet to this destination is sent via R2. To avoid black holing traffic, configure R1 to check the CDP database to determine if an entry is available for the specified next hop address. Verify your configuration using the appropriate commands.

 

Task 4

Configure PBR on R2 and R3 so that when either of their WAN connections to R1 are down, only HTTP and HTTPS should be permitted from the local LAN segment and sent across the R2-R3 WAN link. Assuming that QoS is enabled on the R2-R3 link, this traffic should be forwarded using an IP Precedence of 4. All other traffic from the LAN subnet of the router that lost its WAN connection to R1 should be forwarded with an IP Precedence of 2.

When the WAN link to R1 is up, all traffic should follow the EIGRP route through R1. When completing this task, you MUST adhere to the following restrictions:

  1. You MUST use Cisco Enhanced Object Tracking (EOT) in your solution
  2. You MUST use Cisco IOS IP SLA Operations and in your solution
  3. The Cisco IOS IP SLA Operation should ping the connected IP address of R1
  4. As long as EIGRP routing information is present, PBR should be inactive

Verify the PBR configuration using the appropriate show commands or debugging commands.

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.