www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / Design / CCDA / Chapter 5: Enterprise WAN Design / Enterprise WAN Design – Summary

Enterprise WAN Design – Summary

Remote office locations, such as branch offices or the homes of teleworkers, connect to the enterprise campus via the enterprise edge and the enterprise WAN. When selecting an appropriate WAN technology to extend to these remote locations, design considerations include ownership of the link, reliability of the link, and a backup link if the primary link were to fail.

 

In the Cisco enterprise architecture model, the enterprise edge module allows the enterprise campus module to connect to remote offices using a variety of WAN, Internet-access, and remote-access technologies (e.g., secure virtual private network access). A WAN spans a relatively broad geographical area in which a wide variety of connectivity options exist.

 

The primary goals of WAN design include the following:

 

  • The WAN must achieve the goals, meet the characteristics, and support the policies of the customer.
  • The WAN must use a technology to meet present requirements, in addition to requirements for the near future.
  • The expense of the WAN (one-time and recurring expenses) should not exceed customer-specified budgetary constraints.

 

When designing WAN solutions, you should consider the characteristics of the following modern WAN technologies:

 

  • Time-Division Multiplexing (TDM): A TDM circuit is a dedicated point-to-point connection that is constantly connected. T1 and E1 circuits are examples of TDM circuits.
  • Integrated Services Digital Network (ISDN): ISDN uses digital phone connections to support the simultaneous transmission of voice and data. ISDN is considered a circuit-switched technology.
  • Frame Relay: Frame Relay is considered a packet-switched technology, which uses the concept of virtual circuits to create, potentially, multiple logical connections using a single physical connection.
  • Multi-Protocol Label Switching (MPLS): MPLS is considered a label-switching technology where packets are forwarded based on a 32-bit label, as opposed to an IP address.
  • Metro Ethernet: Metro Ethernet uses Ethernet technology to provide high-speed yet cost-effective links for some Metropolitan Area Networks (MANs) and WANs.
  • Digital Subscriber Line (DSL): DSL provides high-bandwidth links over existing phone lines. A variety of DSL implementations exist. The most popular type of DSL found in homes is ADSL, which allows home users to use their phone line for both high-speed data connectivity and traditional analog telephone access simultaneously.
  • Cable: Cable technology leverages existing coaxial cable, used for delivery of television signals, to deliver high-speed data access to the WAN simultaneously.
  • Wireless: Wireless technologies use radio waves to connect devices, such as cell phones and computers. An example of a wireless application is wireless bridges, which can connect two buildings that have a line-of-site path between them.
  • Synchronous Optical Networking (SONET) and Synchronous Digital Hierarchy (SDH): SONET and SDH both use TDM technology to provide services over an optical network. Because of the optical transport used by these technologies, relatively high-bandwidth solutions are available.
  • Dense Wavelength Division Multiplexing (DWDM): DWDM increases the bandwidth capacity of an optical cable by sending multiple traffic flows over the same fiber, with each flow using a different wavelength.

 

Enterprise edge design uses the PPDIOO approach discussed previously. Specifically, the WAN designer should do the following:

 

  • Determine network requirements
  • Evaluate existing network technology
  • Design the network topology

 

When designing networks to traverse the WAN, a primary design consideration is making the most efficient use of the relatively limited WAN bandwidth. Cisco and other vendors provide a variety of QoS mechanisms that can help in this regard, including the following:

 

  • Compression: By making the packet smaller, it requires less bandwidth for transmission across a WAN. Therefore, compressing traffic is much like adding WAN bandwidth.
  • Link aggregation: Cisco routers support the bonding of physical links into a virtual link.
  • Window size: Network delay can be reduced by increasing the window size (i.e., sending more TCP segments before expecting an acknowledgment).
  • Queuing: When a router is receiving traffic (e.g., from a LAN interface) faster than it can transmit that traffic (e.g., out of a WAN interface), the router delays the excess traffic in a buffer called a queue. To prevent bandwidth-intense applications from consuming too much of the limited WAN bandwidth, various queuing technologies can place different types of traffic into different queues, based on the traffic priority. Then, different amounts of bandwidth can be given to the different queues.
  • Traffic shaping and policing: To prevent some types of traffic (e.g., music downloads from the Internet) from consuming too much WAN bandwidth, a traffic conditioner called policing can be used to set a “speed limit” on those specific traffic types and drop any traffic exceeding that limit. Similarly, to prevent a WAN link from becoming oversubscribed (e.g., oversubscribing a remote office’s 128 kbps link when receiving traffic from the headquarters, which is transmitting at a speed of 768 kbps), another traffic conditioner called shaping can be used to prevent traffic from exceeding a specified bandwidth. With shaping, compared to policing, excessive traffic is delayed and transmitted when bandwidth becomes available, instead of being dropped. Unlike shaping, policing mechanisms can also remark traffic, giving lower-priority QoS markings to traffic exceeding a bandwidth limit.

 

When considering design elements for the enterprise WAN, the following design categories exist:

  • Traditional WAN design:
    • Leased lines
    • Circuit switched
    • Packet/cell switched
    • Remote-access network design
    • Virtual private network (VPN) design
    • WAN backup design:
      • Dial-up backup routing
      • Redundant WAN link
      • Shadow PVC
      • IPSec tunnel

Prev

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.