www.howtonetwork.org

CCNA & CCNP Certifcation Training

  • About
  • Contact
  • FAQ
  • Join
  • Home
  • CCNA
    • ICND1
    • ICND2
    • 101 CCNA LABS
  • CCNP
    • ROUTE
    • SWITCH
    • TSHOOT
    • 101 CCNP LABS
  • CompTIA
    • Security+
    • Network+
  • Design
    • CCDA
    • CCDP
You are here: Home / ICND1 / Day 3 – Trunking, DTP, and Inter-VLAN Routing / Day 3 Labs / VLAN and Trunking Lab

VLAN and Trunking Lab

Topology

 

 VLAN and Trunking Lab

Purpose

Learn how to configure VLANs and trunk links.

Walkthrough

  1. You will need to add IP addresses on each PC. Feel free to choose your own, as long as they are on the same subnet!
  2. On Switch A, set the hostname, create VLAN 2, and put the interface to which your PC is connected into VLAN 2. You can also give the VLAN a name if you wish.

Switch>en

Switch#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#hostname SwitchA

SwitchA(config)#vlan 2

SwitchA(config-vlan)#name 60days

SwitchA(config-vlan)#interface FastEthernet0/1

SwitchA(config-if)#switchport mode access

SwitchA(config-if)#switchport access vlan 2

SwitchA(config-if)#^Z

SwitchA#show vlan brief

VLAN Name               Status    Ports

—- ——— ——————————-

1    default            active    Fa0/2, Fa0/3, Fa0/4, Fa0/5,

            Fa0/6, Fa0/7, Fa0/8, Fa0/9,

            Fa0/10, Fa0/11, Fa0/12, Fa0/13,

                                  Fa0/14, Fa0/15, Fa0/16, Fa0/17,

                                  Fa0/18, Fa0/19, Fa0/20, Fa0/21,

                                  Fa0/22, Fa0/23, Fa0/24

2    60days             active    Fa0/1

1002 fddi-default       active

1003 token-ring-default active

1004 fddinet-default    active

1005 trnet-default      active

SwitchA#

  1. Set your trunk link to trunk mode.

SwitchA#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

SwitchA(config)#int FastEthernet0/2

SwitchA(config-if)#switchport mode trunk

 

SwitchA#show interface trunk

Port        Mode         Encapsulation  Status        Native vlan

Fa0/2       on           802.1q         trunking      1

 

Port        Vlans allowed on trunk

Fa0/2       1-1005

  1. If you wish, permit only VLAN 2 on the trunk link.

SwitchA(config)#int FastEthernet0/2

SwitchA(config-if)#switchport trunk allowed vlan 2

SwitchA(config-if)#^Z

SwitchA#

%SYS-5-CONFIG_I: Configured from console by console

 

SwitchA#show int trunk

Port        Mode         Encapsulation  Status        Native vlan

Fa0/2       on           802.1q         trunking      1

 

Port        Vlans allowed on trunk

Fa0/2       2

  1. At this point, if you ping from one PC to another, it should fail. This is because one side is in VLAN 1 and the other is in VLAN 2.

PC>ping 192.168.1.1

 

Pinging 192.168.1.1 with 32 bytes of data:

 

Request timed out.

 

Ping statistics for 192.168.1.1:

Packets: Sent = 2, Received = 0, Lost = 2 (100% loss)

  1. Configure the same commands on Switch B now. For VLAN creation, put the PC port into VLAN 2, and set the interface to “access” and the trunk link to “trunk.”
  2. Now you should be able to ping across the trunk link from PC to PC.

PC>ping 192.168.1.1

 

Pinging 192.168.1.1 with 32 bytes of data:

 

Reply from 192.168.1.1: bytes=32 time=188ms TTL=128

Reply from 192.168.1.1: bytes=32 time=78ms TTL=128

Reply from 192.168.1.1: bytes=32 time=94ms TTL=128

Reply from 192.168.1.1: bytes=32 time=79ms TTL=128

 

Ping statistics for 192.168.1.1:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

Minimum = 78ms, Maximum = 188ms, Average = 109ms

Next

About Us

This is a free bonus site for members of www.howtonetwork.com

Copyright

The content on this copyright Reality Press Ltd.
Copyright Reality Press Ltd.