Switch Bonus Quiz 1 1. Which of the following statements about PAgP learners are FALSE? Select FOUR answers. Aggregate learners are switches that learn MAC addresses using the ports within the EtherChannel For physical learners, it is important to set the load-distribution method to destination-based distribution Physical learning is the default in current Cisco IOS switches By default, PAgP is able to detect whether a neighboring switch is a physical learner Aggregate learning is the default in current Cisco IOS switches By default, PAgP is not able to detect whether a neighboring switch is a physical learner Physical learners are switches that learn MAC addresses using the ports within the EtherChannel For physical learners, it is important to set the load-distribution method to source-based distribution Question 1 of 28 2. Which of the following is NOT an advantage that switches have over bridges? They support Layer 3 and Layer 4 packet switching They operate at hardware speed using ASICs They allow for the segmentation of the LAN They allow for microsegmentation by allowing individual hosts to be connected to individual ports They have more ports than a bridge would ever be capable of supporting They use VLANs to create smaller logical broadcast domains Question 2 of 28 3. Which of the following statements about the TCN BPDU in 802.1D is TRUE? The Root Bridge continues to set the TCN flag in all Configuration BPDUs that it sends out for a total of 15 seconds The Root Bridge continues to set the TCN flag in all Configuration BPDUs that it sends out for a total of 7 seconds The Root Bridge continues to set the TCN flag in all Configuration BPDUs that it sends out for a total of 20 seconds The Root Bridge continues to set the TCN flag in all Configuration BPDUs that it sends out for a total of 50 seconds The Root Bridge continues to set the TCN flag in all Configuration BPDUs that it sends out for a total of 35 seconds Question 3 of 28 4. What is the default HSRP priority? 110 115 105 100 Question 4 of 28 5. Click on the Exhibit. The Exhibit illustrates the Bridge ID using the Extended System ID. Which of the following are the values of X and Y as illustrated in the Exhibit? X = 6 X = 4 Y = 10 X = 2 Y = 12 Y = 14 Question 5 of 28 6. Which of the following is not a valid port security violation action? Restrict Shutdown Protect VLAN Protect Shutdown VLAN Question 6 of 28 7. What happens when a link within an EtherChannel group fails? Select the BEST answer. The traffic is distributed between the remaining links The traffic is dropped until the link is restored The traffic is re-routed to another link The switch will find an alternative EtherChannel to use The EtherChannel line protocol transitions to a down/down state Question 7 of 28 8. The topology of an active switched network is determined by certain variables. What are these variables? Select THREE answers. The port identifier (MAC address of the port) associated with each switch port The Port Cost to the Root Bridge associated with each switch port The unique MAC address (switch identifier) that is associated with each switch The port identifier (MAC address of the port) associated with each Root port The Path Cost to the Root Bridge associated with each switch port Question 8 of 28 9. Click on the Exhibit. Which of the following accurately describes the fields marked X, Y and Z? X = Proposal, Y = Agreement, Z = Port Role X = Agreement, Y = Port Role, Z = Proposal X = Proposal, Y = Port Role, Z = Agreement X = Agreement, Y = Proposal, Z = Port Role X = Port Role, Y = Agreement, Z = Proposal X = Port Role, Y = Proposal, Z = Agreement Question 9 of 28 10. What is used to communicate and compute the Spanning Tree topology? Select the BEST answer. Switches Port Cost Bridge Priority MAC Addresses BPDUs Path Cost Question 10 of 28 11. When a Non-Root Bridge receives a Configuration BPDU on its Designated Port, it sends an updated version of the BPDU via its Root Port. This is referred to as the propagation of BPDUs. True False Question 11 of 28 12. Which of the following is NOT a traditional MLS component? MLS-SE MLS-RP MLSP MLS-SP Question 12 of 28 13. What feature allows the switch to use the extended system ID, the switch priority, and a single MAC address to build a unique BID for all potential 4094 VLANs? IEEE 802.1D Spanning-Tree Enhancements MAC Address Reduction PVST+ VLAN Allocation Question 13 of 28 14. What is the value contained in the Protocol Identifier (PID) field of the RSTP BPDU? 2 0 1 3 Question 14 of 28 15. What types of attacks does the port security feature protect against? Select TWO answers. Port Spoofing Attacks CAM Table Overflow Attacks CAM Table Replication Attacks ARP Spoofing Attacks MAC Spoofing Attacks Question 15 of 28 16. Click on the Exhibit. What will happen if an additional host is connected to the switch port, e.g. via a Hub? The port will be shut down The port will be protected Nothing, the host will be allowed to send frames The VLAN will be shut down It will be restricted Question 16 of 28 17. The completion of the Configuration BPDU exchange results in the culmination of several events. Which of the following is NOT one of those? Loops in the network are eliminated by blocking redundant paths A Designated Port is elected on every Non-Root Switch in the Spanning Tree domain A Designated Port is elected on the Designated Switch for every segment A Root Switch is elected for the entire Spanning Tree domain A Designated Switch is elected for every LAN segment A Root Port is elected on every Non-Root Switch in the Spanning Tree domain Question 17 of 28 18. What type of switching uses cross-connects to create connections from any port to any other port on the device? Layer 3 switching Layer 1 switching Layer 4 switching Layer 2 switching Layer 7 switching Question 18 of 28 19. Switch EtherChannels using PAgP may be configured to operate in one of two modes. What are these two modes? On Desirable Passive Auto Off Active Question 19 of 28 20. Dynamic VLAN assignment allows a host to be assigned to the same VLAN when it is moved from one switch in the network to another. False True Question 20 of 28 21. Click on the Exhibit. Select the commands that resulted in the output illustrated in the Exhibit. Select THREE answers. The switchport port-security maximum 10 command The switchport port-security violation shutdown vlan command The switchport port-security violation restrict command The switchport port-security aging type inactivity command The switchport port-security aging static 120 command The switchport port-security aging type absolute command The switchport port-security aging static command The switchport port-security command The switchport port-security maximum 5 command Question 21 of 28 22. Click on the Exhibit. The exhibit illustrates a switch port being configured for inter-VLAN routing. Which of the following represents how the router interface connected to the switch port would be configured? R1(config)#interface fast 0/0.30 R1(config-subitf)#description ‘Subinterface For Management’ R1(config-subif)#encapsulation dot1Q 30 native R1(config-subif)#ip add 10.30.30.1 255.255.255.0 R1(config-subif)#exit R1(config)#interface fast 3/0 R1(config-subitf)#description ‘Subinterface For Management’ R1(config-subif)#encapsulation 30 dot1Q native R1(config-subif)#ip add 10.30.30.1 255.255.255.0 R1(config-subif)#exit R1(config)#interface fast 3/0.0 R1(config-subitf)#description ‘Subinterface For Management’ R1(config-subif)#encapsulation dot1Q native 30 R1(config-subif)#ip add 10.30.30.1 255.255.255.0 R1(config-subif)#exit R1(config)#interface fast 3/0 R1(config-subitf)#description ‘Subinterface For Management’ R1(config-subif)#encapsulation dot1Q 30 native R1(config-subif)#ip add 10.30.30.1 255.255.255.0 R1(config-subif)#exit R1(config)#interface fast 0/0.0 R1(config-subitf)#description ‘Subinterface For Management’ R1(config-subif)#encapsulation dot1Q 30 native R1(config-subif)#ip add 10.30.30.1 255.255.255.0 R1(config-subif)#exit Question 22 of 28 23. Click on the Exhibit. Which of the following is possible based on only the output illustrated in the Exhibit? Select THREE answers. R2 has the IP address 192.168.1.2/24 configured on its Fa0/0 interface R2 has the higher IP address R1 has the IP address 192.168.1.1/24 configured on its Fa0/0 interface R2 has the lower HSRP priority R2 is the standby router R2 has the lower IP address R2 is the primary (active) router R2 has the lower HSRP priority Question 23 of 28 24. Which of the following statements about PAgP protocol packet forwarding are FALSE? Select FOUR answers. DTP and CDP send and receive packets over all the physical interfaces in the EtherChannel DTP and CDP send and receive packets over all the logical EtherChannel interface For a Layer 2 EtherChannel trunk, the trunk sends and receives PAgP frames on the lowest numbered VLAN STP always chooses the first operational port in an EtherChannel bundle DTP and CDP send and receive packets over the first operation interface in the EtherChannel For a Layer 2 EtherChannel trunk, the trunk sends and receives PAgP frames on the lowest numbered port STP always chooses the lowest numerical operational port in an EtherChannel bundle Question 24 of 28 25. Which of the following VLANs is reserved and is used for IEEE 802.1p priority tagging for voice traffic 4095 1 1005 0 1024 Question 25 of 28 26. In the 802.1D BPDU, the Flags field is used for the Topology Change and Topology Change ACK flag. Which TWO statements are FALSE about this field? If the LSB is set, this indicates a Topology Change Acknowledgment (TCA) flag If the MSB is set, this indicates a Topology Change (TC) flag If the MSB is set, this indicates a Topology Change Acknowledgment (TCA) flag If the LSB is set, this indicates a Topology Change (TC) flag Question 26 of 28 27. What is the MAC address range used by HSRPv2? 0000.0C9F.7000 to 0000.0C9F.FFFF 0000.0C07.F000 to 0000.0C07.FFFF 0000.0C07.AC00 to 0000.0C07.ACFF 0000.0C7F.F000 to 0000.0C7F.FFFF 0000.0C9F.F000 to 0000.0C9F.FFFF Question 27 of 28 28. At which plane is routing information, routing protocol updates, and other control information, stored and exchanged? Management Forwarding Routing Data Control Question 28 of 28 Loading…